z dd 3d models

This is a folding phone holder. One of the problems I had was that to use my phone with my WRC wheel it needed to be higher and it blocks the screen. With this I can just flip it down. ... Parts.2 Magnets 11x6x32 8mm bolts2 Skate board bearingsOn...

CP Electronics - Enhanced Building Distribution Module Relay Primary Module Dedicated Application Device

USS Johnston DD557 (Fletcher-class) was a World War II destroyer served in United States Navy and sunk in the action. ...Her wreck is the deepest surveyed shipwreck when rediscovered and identified in March 2021.

Main page: https://www.printables.com/model/218461-voron-revo-mount-and-fanducts-v2

Replacing a worn-out gasket is essential to prevent water from seeping into your engine. This can cause serious damage and lead to costly repairs. To replace a worn-out gasket, follow these steps: 1. First, locate the old gasket and remove it...

I couldn't find a Hero me base compatible with a an e3d v6, Wham Bam Mutant, and Hero me Gen 5, so I was forced to attempt a remix. ... See notes below!

This fan duct is based on EvoCivic's Sovol SV04 version. worth printing at least from PETG or any more heat-resistant filament. i printed my test version from PLA, but later on I will definitely replace it with something more resistant. ... ...

customized with 3D Slash!

Ball size worked for me, however if it's too small you can add a few layer of tape around it.

Remixed the original, now supporting larger phones or small tablets.

USS Kidd (Fletcher-class) was a World War II destroyer served in United States Navy and now she is a museum.

I took a look at the design and decided that I wanted to make it to where it could be printed with no supports, use the original hotend mounting screws, as well as support direct drive extruders (for my case, the OMG DM1) I also decided to chop off...

Customized version of https://www.thingiverse.com/thing:5462472 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5462472

Enlarged the filament passage through hole to allow PTFE tubing to reach all the way up to the hobbed pulley/idler area and created a channel for easier collet locking on the E3D v6 hotend that secures PTFE tubing in place. Made channels on the...

Customized version of https://www.thingiverse.com/thing:5462472 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5462472

I've searched a lot for upgrading my old extruder to a direct drive one. I've found lots of nice designs on this website but I wanted to design my own with the following targets : Using only parts I had in my spare parts Fits Prusa i3 Rework style...

This model is built near to scale. It is very detailed and a high polygons model. There is a lot of detail on all weather decks. This model is fully textured and has a lot of animatable features: propellers, rudders, guns and weapons platforms, radar...

I designed and manufactured a 120-tooth precision gear wheel using Tinkercad, specifically tailored to fit the Sony WM-D6 Pro line of professional cassette recorders, not walkmans. ...Enjoy!

Human Clone Generation Unit model\nTotally Reconfigurable Language Engine integrated.

Micro Swiss Linear Rail Direct Drive - BLTOUCH Mount

Remix of spool holder by ImpY to mount on the side of the Sapphire Plus vs the front. ... This is the base/brackets only, the rod is unchanged and should be grabbed from the original thing.

I didn't design this model from scratch. This is my first experience building complex models. If someone were to 3D print it, I'd be thrilled to see a photo. ...The prints require approximately 500 grams of plastic and two days to complete, with a layer...

Y-tensioner (for ender 3, V2,PRO) modified for installation of a direct drive (see my YT chain with direct drive links). ... Modified by SIX SAUER ;-)

It is in times of great need when inspiration comes to your door.I was looking for a bracket so I can mount my ADXL345 accelerometer on my Ender 3 V2 Neo, which I have modded with a beautiful firmware, nothing else than Klipper. So, I thought I have...

No information is available about this individual.

This is an incredibly specific print. ...If you just so happen to have this direct drive upgrade for an Ender5 and are using a Palette then you might be interested in this.

I couldn't find a Hero me base compatible with a an e3d v6, Wham Bam Mutant, and Hero me Gen 5, so I was forced to attempt a remix. ... See notes below!

customized with 3D Slash!

This is a meticulously detailed replica of the US Navy's aircraft carrier, showcasing an astonishing level of intricacy. Numerous complex details are present throughout the model, including meticulously rigged fuel hoses, sliding hangar doors that...

Designed as a scale model of the illustrious USS Fletcher, this precision recreation has been crafted with meticulous detail. The creator chose the renowned 3D modeling software Blender, known for its versatility and robust features. ...Using Cycles, a...