z chains 3d models

Human: I created this Z-axis drag chain to work seamlessly with the X-axis chain, which was originally designed by TNS (https://www.thingiverse.com/thing:2105040), and the Electronics Case designed by Lindkj...

... With this setup, you can securely attach the @johnniewhiskey https://www.thingiverse.com/thing:2920060 cable chain for your Z and X Axis. The part also anchors to the top of the extruder, requiring a longer M3 screw to secure it firmly in place.

... for AM8 metal frame upgrade. Small zip tie slots have been added and one M3-8 screw and M3 nut are needed to attach x mount to x-z mount. Also needed are 3 M3-30 to mount the x motor. ... Extending wire from print head to main board is a must.

... ...Despite the challenge, I managed to secure it in place and the shelf now enables the drag chain to move smoothly along its path. ... To utilize this modification, you'll need to swap out the original 2.5-inch bolt for a longer 3-inch one.

After installing the wiring through that chain and carefully tucking the extruder wires, who wants to go back and undo everything just to remove a couple of links or install some other drag chain adapter that forces you to run the wiring through it...

A simple yet effective bracket to secure a thin cable chain to your MPCNC's Z Axis. It fits perfectly with the Nema 17 motor in place. This design utilizes a wedge similar to the head-stem found on bicycles, which securely grips the inside of the...

http://www.thingiverse.com/thing:568551 Clamps onto one of the z-axis to allow mounting of the chain. Uses M3 Hardware. Needs M3x25 for the clamp and lock nut [I'm going to try a zip tie first to pull clamp tight] and two m3x* to mount the end clip...

Since I turned my spool holder 90 degrees towards the front of the printer, I decided to install this cable chain at the back. To build it, you'll need 28 shackles and 30 lids. I printed the lids with a horizontal expansion of -0.15 to -0.2, but...

Use standard 20x10 cable chain. ... Unfortunately, you will have to extend extruder & X motor cables. Udpate 22.01.2023: stronger bottom mount + added bed for the chain.

Hello, here is the mounting bracket for attaching a tow chain above the motor.

For 10x20 drag chain. ... Printer brand: TwoTrees Printer: Sapphire Plus Rafts: No Infill: 10% Supports: Yes Filament material: PLA

I didnt like how the bed wires on my Sapphire Plus were just dangling, so I designed this to use a small cable chain.

... ... Perfect for Cable Chains Measuring 18 Millimeters in Width, 15 Millimeters in Height, and a Length That Can Be Customized. ... Additional Components Will be Added to This Collection as They Are Printed and Documented with High-Quality Photographs.

The cable chain extra nut holder is designed to work seamlessly with the cable chain found on thingiverse at http://www.thingiverse.com/thing:176819. Print Settings: Printer: K8200 Rafts: The raft setting doesn't affect this design's...

The original design was giving me some trouble, so I built a new version that's fully compatible with the Z-axis motor. ...Hopefully, this one will be more to your liking.

I decided to mod the original design to better suit a custom-printer cable chain link (This is the same link found here: https://www.thingiverse.com/thing:2920060) The version pictured for the bottom mount has holes in it but they aren't needed. ...

MPCNC cable chain mounts are specifically designed to fit 25mm pipes, with built-in nut traps that secure M3 bolts tightly in place. ...This mount features a specialized design tailored for aluminum rails and is perfectly suited for use with the...

Bill of Materials: "X axis stepper motor" 3 M3 x 35mm cap 10 x 15mm drag chain Print Settings Printer: Ormerod 2 528.4 Rafts: No Supports: No Resolution: 0.2mm Infill: n/a Notes: The fastening points should be printed vertical with support, the rest...

Bill of Materials: * X axis stepper motor * 3 M3 x 35mm cap screws * 10 x 15mm drag chain links Print Settings: Printer: Ormerod 2 (528.4) Rafts: No Supports: No Resolution: 0.2mm Infill: Not applicable Notes: The fastening points should be printed...

... is 4.5mm and 5mm. ***EDIT V0*** An error on the edge was detected in the original file, then another on the block chain edge. This has been corrected. ... Please don't hesitate to let me know about any problems or improvements you would like!

ABS is more flexible. This is a Z-Axis Chain Link for JGAurora A5s (Possible other Printers). This is re-mixed from the chain (OLD LINK ONLY) The New-Link is not Re-Mix https://www.thingiverse.com/thing:3954315 That I Modified for my use. I got tired...

# Disco Ultimate in 3DLD Style \r\n# Part 2 of 3: "X" and "Z" Axis with Cable Chain and Extrusion \r\n\r\n**Part 1 of 3: https://www.thingiverse.com/thing:3691620**\r\n**Part 2 of 3: this post**\r\n**Part 3 of 3:...

Regarding my Y chain remix, there is also a Z chain remix available. This remix mainly originates from https://www.thingiverse.com/thing:3378510, https://www.thingiverse.com/thing:3578592, and various dependent parts. You won't need all the...

I removed the filament guide from the mount.

Hi everyone, welcome to the enhanced cable chain X axis Z assembly, which offers increased flexibility over traditional systems due to the integrated X/Z cables.

Using the "Big" Chain at https://www.thingiverse.com/thing:611593 for Z, and adding some parts for combination with my Fan Duct at https://www.thingiverse.com/thing:2763931. The "Little" X Chain is also the Open Cable Chain, but scaled to 70%. It...

used the "big" chain https://www.thingiverse.com/thing:611593 for z and added some parts for combination with my fan duct https://www.thingiverse.com/thing:2763931 the "little" x chain is also the open cable chain, but scaled to 70%, works perfect...

Funfair - tower chain carousel (z-scale)Assembling:Paint to your taste and assemble as seen in the picture.Use florist’s wire, annealed, 0,8mm as „chains“, cut to size & bend 12 pieces using the bending template.Printing:Print the the wider side in...

[Z-Axis cable chain](https://www.thingiverse.com/thing:3769941) [Original connector plate](https://www.thingiverse.com/thing:4625117) [X-Axis connector plate](https://www.thingiverse.com/thing:4749290) [X-Axis cable...

Z-Axis cable chain Original connector plate X-Axis connector plate X-Axis cable chain If I was smarter, I would have just designed a way to use the same chain links in both directions, but I'll leave that to others to make a remix who want to do...