z cable 3d models

I'm implementing a straightforward cable organization system for my X and Z axes.

This is meant to replace the z-chain lower mount on an Ender Switchwire conversion so that you can have an m16 cable gland for an umbilical

I created this part for my Ender 3 Neo, because if the Z axis is more than 200 mm, the cables tended to throw my bed out of adjustment. This cable clips mounts directly on the Z stepper type 42-34 from Creality. There is the passage for a 3.6 mm...

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

The Kwixson Adjustable Z endstop has a 4mm hole-bearing protrusion, designed for securing the x-axis motor and endstop's electrical wiring. This isolates movement of the wiring from its connection point to the motor and endstop, protecting it at...

This is an evolution of my Z axis parallel drive, taking advantage of the cable to isolate oscillations caused by a bent or misaligned threaded rod, which normally appear as horizontal ridges in the print. The Z axis motor has been moved to the top...

I adapted ElectricWaste's outstanding work to enable the installation of the Axe Z support under the spooler of the Longer LK4 support.

Tento držák koncového spínače je určen pro tiskárny Průša i3. ...Součástí je i držák stavitelného šroubu pro přesné doladění osy Z. ...Další info ze stavby zde: http://forum.sakul.cz/viewtopic.php?f=12&t=985

This end-stop holder is designed specifically for Prusa i3 printers. ...It comes with a built-in adjustable screw mount for precise Z-axis alignment. ... Additional project details can be found here: http://forum.sakul.cz/viewtopic.php?f=12&t=985

... existing johnniewhiskey set, I discovered that some Ender 3 Cable Chain adapters required modifications to accommodate the cubic frame of my Ender 5 printer. Consequently, I created a custom adapter to securely hold the Z-Axis cable bundle in place.

Refer to origin of this remix:https://github.com/tanaes/whopping_Voron_mods/tree/main/Z_belt_cable_cover The difference is that this version fits narrower 2020 extrusion T-slots (original didn't fit mine - they were intended for a bit wider T-slots)....

This is a Cable holder for the z axis for the Artillery Genius.

A Quick and Dirty Fix to Align the Z-AXIS Chain with the Ender 3 Hot End Front Cable Chain X-Axis Mount This hack was designed in Tinkercad. ... Edit it online at https://www.tinkercad.com/things/8xCVne7pMBZ

A quick and dirty remix to align the Z-AXIS chain with the Ender 3 Hot End Front Cable Chain X-Axis Mount This object was made in Tinkercad. ... Edit it online https://www.tinkercad.com/things/8xCVne7pMBZ

The "Open cable chain" by Vanson reduces the maximum length in Z-axis, causing the chain to touch the screen control and screw on the right when moving the extruder to the top-right position. To resolve this issue, I've merged the cable chain from...

I used brackets from Thingirob but when I decided to start hiding all my cables, the right Z bracket needed some modifications to go along with the extruder mount I designed (see link below). This modified bracket allows you to continue down with...

I placed the sixth link from the top at the back, allowing the extruder cable to go underneath the Z-axis motor. This makes it shorter and prevents the printer from reaching its maximum height. I hope you like my design! ...If you use it, I'd love to...

I liked the Ender 3 MSDD cable chain that Abmillh did, but the Z and X mount did not clear on the CR10S for two reasons, it didn't line up with the bed cable, and it was too tall causing it to hit on the bed levelling knobs, printed or otherwise. ...

It's a **Z-Axis chain connector** for the two holes, that are on the Z-Axis. You'll need some **super-glue** to get the two parts together and **two M4/M5 screws** with wide enough heads and nuts. They can't be too long, or they will block the...

DescriptionThis is inspired by Prusa MINI X-Axis cable protector from @Manfred. I use this¨"remixed" model for Z axis and Extruder motors. ...For X axis I use the original protector.Printing15-20 % infillPLA or PETG (recommended)STL file is...

The cable mess on the right side of the device, next to the z-motor, was begging for attention. However, the shape didn't exactly invite me to create a hard cover that would do it justice. After experimenting with TPU, a new material for me, and a...

guide câbles en Z, impression 0.2 . ...Fixation par 2 x M3*10 et écrous.

A quick and dirty remix to align the Z-AXIS chain with the Ender 3 Hot End Front Cable Chain X-Axis Mount This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/8xCVne7pMBZ Print Settings Printer Brand: Creality Printer: ...

... Box. ... Discover this ingenious cable bracket on Thingiverse, a platform where makers and DIY enthusiasts come together to share their creations. ...Visit https://www.thingiverse.com/thing:3688967 to explore the details of this innovative design.

... It is tight but it will lock in place and hold the chain securely. To get full range of the Z you need to cut just the zip tie at the bottom of your ender 3 v2 that holds it in place under your printer and move it out around the outside. ...

The original design was giving me some trouble, so I built a new version that's fully compatible with the Z-axis motor. ...Hopefully, this one will be more to your liking.

This upgrade enhances the bracket for the z-probe sensor PCB, offering a more reliable fit. ...The latest revision ensures seamless integration during automated calibration, eliminating potential interference with diagonal movements.

... cover and the cable. Make sure that the sensor for the X-Axis sticks out a bit further that the Cable Protection. Otherwise the exdruder unit might touch the Cable Protection. ... This is a remix from https://www.thingiverse.com/thing:4295171

I have designed 2 versions, a normal one to fit directly on the Flex/Cable and another one to install together with a clamp for a better grip on the Flex/Cable. Any of the 2 versions is a good improvement for our printer. During installation in the...