z cable 3d models

its a bracket that mounts to the z motor on an ender 3, and allows cleaner cable routing. ...Print it on its side with supports from build plate.

... extruder en did not had the hardware lying around. ... This is a cable chain for the Z axis and no hardware required Also remixed the chain link from diogosantos88 so it would hinges backwards (see foto) 22 cables chains are needed for the Z axis.

I was tired of looking at the messy cable harness at the Z-axis, so i designed this little cable holder to mount on the lower roller bearing at the Y-axis motor. Unmount bolt and keep bearing in place with one of the umbraco keys. Mount cable...

I upgraded the MPCNC's Z-axis drag chain/cable carrier to withstand the rigors of its heavy-duty drag chain, which was consistently causing failures in the original design. ...To compensate, I significantly expanded the carrier's dimensions to...

You'll require the cable chain assembly found at this specific URL: https://www.thingiverse.com/thing:11978. ... This will provide you with a total of 48 cable chain links and end pieces, combining both the Y-value and Z-value quantities mentioned.

This was a compilation of various components sourced from Thingiverse, with some alterations to ensure precise Z-stop adjustment and cable management. I've incorporated an updated file featuring a hole for accessing the foot screw. Print Settings: ...

Updated Version with Hotend https://www.thingiverse.com/thing:3571641 This is a one piece part for the Ender 3 that snaps around the extruder motor and will allow you to mount @johnniewhiskey https://www.thingiverse.com/thing:2920060 cable chain for...

...... This one-piece part is designed to fit around the extruder motor on the Ender 3, allowing you to easily install a cable chain for your Z and X axes. The part also attaches to the top of the extruder, requiring a longer M3 screw for secure mounting.

Modified the cable chain mount to include a z stop adjustment directly into it. The only file modified was the motor bracket, but a STL of the other files is included for reference purposes. Sixteen links and a long chain piece were utilized in this...

Another essential upgrade kit for your Z-axis motor on the Ender 3 printer system has arrived.

[To install the Ver2.0 Z-Axis holder needs to temporarily remove the pom wheel under the X-axis‘ motor once.]

This cable guide ensures you don't obstruct the cables and filament tube in the upper frame of your printer. ...It was specifically created to fit the Anycubic i3 Mega, utilizing the led light strip designed by @masher55...

I chose to install my bowden extruder at the top crossbar of my QUBD ThreeUp printer. ...I created a bracket by combining my z-wobble design and my NEMA 17 motor mounting design.

I purchased a 10x10 cable drag chain on Aliexpress (the link is https://es.aliexpress.com/item/Free-Shipping-Best-price-10-x-10mm-L1000mm-Cable-Drag-Chain-Wire-Carrier-with-end-connectors/32369095707.html). To complete the project, I just needed to...

Upon being compelled to swap the connector for the thermal cut-out, I opted to add a cable tie-down as well, in an effort to alleviate stress on this component. ...Simultaneously, the tie-down served to replace the stand-offs beneath the circuit board.

Alternative cable support using a tie-wrap is significantly easier to print than before. As this project continues to evolve, it's clear that some adjustments were necessary - in my case, cutting a small corner after printing was required to ensure...

I modified the original to add better strain relief for the X axis ribbon cable. The holes in the cover were designed for M2 x 4mm threaded inserts but you can use a washer and nut if you don't have the inserts. ... Excuse the picture, I haven't had...

This is the Z-axis drag chain mount that matches the XY-axis set I designed right here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for four bolts and nuts, but you only need two in each one. Seriously, stop over-tightening it -...

This is the Z-axis drag chain mount that matches the XY-axis set I designed here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for 4 bolts and nuts, but you only need to use two in each one. No seriously, stop tightening it. :) You...

This is the Z-axis drag chain mount that matches the XY-axis set I designed here. http://www.thingiverse.com/thing:1272581 I made EMT clampholes for 4 bolts and nuts, but you only need to use two in each one. No seriously, stop tightening it. :) You...

This is a remix. ... The holes doesnt fit with my i3 mega s so i made this version.

Añadí soporte para detector de filamentos para poner dos racores de M6 con tubo PTFE.

Climb onto the steper and transport the cable chain to the z-axis location.

Soporte para sujetar Cable_Faja de eje Z en Artillery X1

... available on the market. To access this impressive cable holder and probe bracket, simply visit Aliexpress at https://www.aliexpress.com/item/3D-printer-auto-leveling-external-sensor-Z-probe-compatible-with-most-nozzles/32834946465.html.

Z axis limit was not adjustable, I had the springs on the bed almost at their limit and after one print noticed that there was movement during the print and had to reset the bed level for the second test print 2.Cable to the extruder dragging on the...

This is a remix to add a cable guide for the Z axis. Print the parts as they are. No need for supports. Don't hesitate to ask me if there are any modifications to be made.17 part for Z15 part for XIl s'agit d'un remix pour ajouter un guide-câble pour...

The original links were also very unstable and frequently disconnected due to the force of the cable, prompting me to redesign them for added stability. Additionally, one part is now integrated into both the Z and Y base mounts. Notably, my...