z brace 3d models

This is a Z-Brace kit I designed specifically for Maker Select/Wanhao Duplicator printers. My goal was to create a simple and straightforward Z-brace with as few parts as possible. To build this brace, you'll need the following printed components:...

Rear Z Braces for the Creality CR Series - A Simple Upgrade These rear Z braces are designed to be installed on the Creality CR series, without interfering with any stock parts. However, you may notice a slight reduction in print height of around...

Try using an infill of 10-20% when printing, as higher settings make it difficult to clamp the z-brace base to the rods (which are 5/16 or 8mm in diameter). Be cautious with the camera when placing it in its case. Some eBay RPi cameras have...

Z-Brace for the ender extender 400XL, requires following hardware:M8 threadM5 bolts M5 T-NutsOptional: washers Additional tip: my Z extrusions were not entirely flat on the bottom side. I used a thin metal plate to compensate for this which...

I was really fond of the frame mount LED holder, but I hit a couple of snags: Mounting it on the top rail cuts down on max z travel The light beams into my octo pi camera, which is now positioned in a front corner So, I revamped the design to attach...

Since HillbillyZT's mount wouldn't work with the Z brace mod, I designed my own. This camera mount is compatible with any camera featuring a standard 1/4" tripod mount, but it was specifically designed to work with my Logitech C615. When used with...

HillbillyZT's mount wouldn't work with the Z brace mod, so I designed my own. This is compatible with any camera that has a standard 1/4" tripod mount, but I specifically designed it to work with my Logitech C615. When used with the C615 (or any...

I designed a simple camera mount for my Wanhao Duplicator i3 with Z brace mod installed because HillbillyZT's mount wouldn't work with the Z brace modification. I came up with my own design. This mount is compatible with any standard 1/4"...

Rear Z Braces for the Creality CR Series These braces should not interfere with any stock parts, but installing them might result in a loss of 5-10mm of print height. If necessary, I can adjust the angle of the rods upon request. No removal of...

This is a remixed version of an Inches Cable Conduit cable concealer box specifically designed for Wanhao Duplicator I3 and Monoprice Maker Select v1 and V2 printers that have been upgraded with the Z-brace mod kit structural stability kit. It fits...

(The clamp is positioned at a 20-degree angle) I didn't cut the Z bracing rods and instead used them as spool holders with a small hook to secure an unused M8 rod after the upgrade. ... My Z axis is now perfectly aligned and very stable Spool Cone Link:...

This bracket allows users of the Monoprice MP10 to utilize the stock CR10 Z-brace without damaging the front frame. The design accommodates M5 hardware throughout, ensuring a seamless integration. Two screws, specifically M5x8, are required for...

This bolts to the frame and the upright with M5 bolts and T-nuts to stiffen the Z axis some and provide a fixed mounting point for the Z Limit switch. File contains a brace for the right side also. ... Printed in Sainsmart Petg Nozzle 240-242C Bed...

This is my Z axis brace design for the Ender Extender XL and 400XL. This design will work with the Ender 3 and 3 Pro. It has worked very well for me and I hope that it benefits all of you. I purchased the Ender Extender kit from...

This is a PTZ mount for mounting a Raspi camera onto the Z brace of the Wanhao i3 or Monoprice Select printer, providing a pan-tilt-zoom system with an extension arm. This setup allows users to move the camera out of the way and take time-lapse...

YMMV Post-Printing Required Parts 1x M3x16mm bolt (minimum) 1x M3 hex nut Instructions 1) Place the Z brace coupling on the threaded rod at the desired height. ...2) Using an M3 hex nut and 16mm bolt, secure the coupling to the rod (Don't over-tighten)...

I didn't like the small gaps over the Y extrusion, and realized I could fill all of them with colorful hexagons fit perfectly to the design. This was designed in TinkerCAD, with the main Z brace acting as a hole to cut the exact hex...

A remix of Azza's "Z braces for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers."http://www.thingiverse.com/thing:921948 Just print the top_left, top_right and 6 of the balls from Azza's braces along with the 4 STL's...

Tinkercad is very easy to get the hang of.**** This is a remix and expansion of this thing by MadHatter3D but Thingiverse remix appears to be broken so I'm linking here to the original to give credit: https://www.thingiverse.com/thing:4182718 With...

A versatile Raspberry Pi camera mount that adjusts securely to the arms on a Z-brace mod. Prints smoothly without supports and holds firmly in place. Thanks to the peg's symmetry, you can easily mirror the parts in your slicer to position the camera...

A compact, adjustable Raspberry Pi camera mount that attaches to the arms on a Z-brace mod. Prints easily without supports and holds securely. Besides the peg the parts are otherwise symmetrical so you can mirror them in your slicer if you want the...

A compact, adjustable Raspberry Pi camera mount that attaches to the arms on a Z-brace mod. Prints easily without supports and holds securely. Besides the peg the parts are otherwise symmetrical so you can mirror them in your slicer if you want the...

Another Z-brace modification specifically designed for the Wanhao I3 Plus, which should also work seamlessly with the Plus Mk2 model. Installation is effortless and requires minimal materials. A standard roll of filament will suffice to get started.

These printable parts design a rear z-brace for the Wanhao i3, made to fit a Monoprice Maker Select V2. Clear access to all components from the front is maintained by placing them in the back. This design accommodates 5/16 threaded rod, commonly...

Following the lead of FilamentCorner's z Brace and z Extensions (Z-Kit), I decided to make a hybrid design that moved the braces to the back of the printer so as to be out of the way. All of this is based on AzzA's original work which can be found...

I created these z-brace components because the i3 Mega unfortunately has a very wobbly Z-axis, and the resulting vibrations are reflected in the print. For the correct assembly, you will need to prepare each side with: 50 cm threaded bar M8 4...

For the CR-10S5, this is a remix of the turnbuckles from the Z-brace kit by Buildituniversity. I extended the turnbuckles by +50mm and +75mm, so you can use a 24in threaded rod off the shelf, instead of buying longer rods and cutting them down to...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 These nuts are designed to fit the 3/8" components of the Z-brace http://www.thingiverse.com/thing:1359774. The metal 3/8" nuts available from Bunnings in Australia do not fit the...

... 2 57cm 8mm threaded rods and 8 x 8mm Lock nuts. Completely redrawn but based on the design by @butchja It does mean you will lose around 2 to 3 cm Z height on the printer. ...If I have time I would redesign the top bracket not to lose the height.

The Eryone Thinker's impressive stature demands sturdy support, making frame braces a necessity. To secure this behemoth, you'll need two 57cm threaded rods and eight 8mm lock nuts. This modified design, inspired by @butchja's original concept,...