z banding 3d models

I created this to test "Z banding" between the two Z threaded rods on a Prusa i3. DO NOT USE IF X BED WIDTH IS LESS THAN 195mm!!! ... Print Settings Printer: Prusa i3 ...

Most Z banding is caused by bent or misaligned lead screws/threaded rods. By removing the gantry from the Z axis and using gravity to hold it in place (which is more than enough), you're disconnecting the gantry in both the X and Y planes. This...

Scale if you want. ...Meant to show how much your z is wobbling

A simple test cylinder, good print to show how consistent or not your Z-axis is.the Base is 2mm thick so you can measure if your z-offset is correct. The cylinder is 100mm so you can measure for your Z-axis e-steps. ...Base is 40mm x 40mm so you can...

After much research and testing, I have concluded that this is the best choice for a bent threaded rod on the Z axis. These are 2x 3d printed parts that use beads and magnets to absorb the unevenness of the threaded rod. This way there will not be...

I couldn't find any simple test piece for debuggind Z axis issues (e.g. Z wobble), so I made this simple test cylinder piece. The idea is to print it using **vase mode** (in Cura the setting needed is called "Spiralize outer contour"). ...This way...

Firmware changes: - either change in firmware files and reflash, or connect to octoprint/pronterface terminal and use gcode below - Set Z steps per unit to 2040 (M92 Z2040)(this may be different if you're using different setting to start with, which...

After tightening official Anti-Backlash Nut Block issue was gone but returned after few days of printing. After release of V-Core 3.1 I liked how they resolved same issue on bigger printer so I gave it a try.  Main purpose of this build was to add...

The design aims to minimize bed movement even with a slightly bent or off-center threaded rod, by encapsulating the nut in a low friction "wobble space" that allows travel only in the X and Y axes. The 5/16" aluminum bed setup has been fixed in the...

A personalized adaptation of http://www.thingiverse.com/thing:101308 has been crafted using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=101308). To create this, 516 pieces were printed on a wood bed with print_tool...

Customized version of http://www.thingiverse.com/thing:101308 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=101308 Instructions Using the following options: parts =...

Customized version of http://www.thingiverse.com/thing:101308 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=101308 Instructions Using the following options: parts =...

This model is a customized version of the one found at thingiverse.com/thing:101308, generated with their customizer app. ...It features multiple settings available for user configuration, such as printing tools and parts, set here to yes and 3mm...

Customized version of http://www.thingiverse.com/thing:101308 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=101308 Instructions Using the following options:...

Design by Human: Thing #101308 Customized from the Original Model Available on http://www.thingiverse.com Assembled with Customizer! ...Your Design Made Easy Visit Our Site to Explore More Options...

Human-Made Edition of the Original Design from Thingiverse Built with Customizer, a One-of-a-Kind Online Tool: https://www.thingiverse.com/apps/customizer/run?thing_id=101308 The Instructions Are Here: We Used the Following Settings: Print...

Check out this thing I came up with: https://www.thingiverse.com/thing:201318 Made using Thingiverse Customizer! ...Check it out: https://www.thingiverse.com/apps/customizer/run?thing_id=201318 Instructions Using the following options: print_tool =...

This is a personalized adaptation of http://www.thingiverse.com/thing:101308, which was generated using the Customizer! at http://www.thingiverse.com/apps/customizer/run?thing_id=101308. The customization features include a 3mm aluminum bed and...

This is a personalized adaptation of http://www.thingiverse.com/thing:101308, designed with Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=101308). ...It features 516 aluminum bed and a print tool, as specified by the user.

This custom-made item is based on Thingiverse's design (http://www.thingiverse.com/thing:101308). ...It was created using Customizer (http://www.thingiverse.com/apps/customizer/run?thing_id=101308), and the specifications include no print tool and a 5mm...

Customized Version of Thing #101308 Created Using Thingiverse Customizer http://www.thingiverse.com/apps/customizer/run?thing_id=101308 Created With Options in Effect Print Tool Disabled Number of Parts Three-Millimeter Aluminum Bed Material...

A customized adaptation of the design available at http://www.thingiverse.com/thing:101308 has been created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=101308). ...Key features include printing with a tool and...

This customized item can be found at http://www.thingiverse.com/thing:101308 and was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=101308). ...To print it, ensure that you select 'yes' for the print_tool...

This is a customized version of the design found at http://www.thingiverse.com/thing:101308, created using the Customizer app with the settings for a 516 aluminum bed and print tool enabled...

The customized version of this design can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=101308, where you can create your own unique model using the provided Customizer tool. For printing, it is recommended to use a 516 aluminum...