z axis stabilizer 3d models

This tweak will enable Z Wobble in the HICTOP Prusa i3 without requiring a re-print of the z carriages.

Ender 3 Lead Screw Stabilizer. ... I fixed it because it didn't fit on the 20x20 bare metal.

Required hardware includes a stabilizer made from high-quality half-inch steel hollow tubing, along with four 3M 25mm screws and three 3M Locknuts.

The stabilizer is specifically designed for the latest model of the CTC Printer, which features a shorter rod with an 8mm diameter. This particular design allows you to insert a 14x8x4 bearing, ensuring it stays securely in place. The bottom plate of...

There seems to be 3mm difference in the offset between the Z screw and the frame when comparing the Ender 3 Pro to the Ender 3 V2 Neo. ... Have remixed MammothMGs design to close that gap.

Materials Needed: For Both Side Stabilizers 4 M3 screws measuring 10mm in length 6 M3 screws measuring 35mm in length 10 M3 autoblock nuts 4 M3 hammer nuts for aluminum profiles measuring 2020 8 M3 washers 2 linear shafts measuring 8mm and 630mm in...

The "Ender 3 Lead Screw Stabilizer" project was published on September 2, 2018, and can be found at www.thingiverse.com/thing:3080912. After making some adjustments to the original design, I no longer need to secure it with screws. ...Instead, I simply...

The top section enables the installation of a bearing at the top of Z rods and limits wobble due to slightly misaligned rods. Bearing size: 22x8x7. Printed in PLA with layer thickness of 0.2mm. The lower section further reduces wobble by...

... revision: an updated version of this item has been posted, characterized by its open design at both ends allowing use on earlier models as well as positioning beneath the print carriage. This revised device bears the filename Z Clip R1 Custom.stl.

... for potential clearance issues with the X carriage assembly. For this project, I repurposed my upgraded threaded Z rods. ...However, this is still a work in progress as I aim to optimize printability by potentially removing some curved elements.

Didn't like niches in original z-axis stabilizer so I designed a simple cover to hide them.

The other Z axis stabilizers didn't work for me, so I made my own. ...I use 608 skateboard bearings.

Didn't want to give up my handle just to install a Z-Axis stabilizer, so I mixed them.

Z-Axis Stabilizer for Velleman Vertex K8400 3D Printer Designed to Utilize Radial Bearings Measuring 8x16x5mm. Print Settings Include: Rafts Are Not Recommended. Supports Should Be Disabled. A Layer Resolution of 0.2 is Standard. ...25 Percent Infill...

Creality Ender 6 Z-axis stabilizer with ball bearing. Optimized for easy printing. Print without support. Mounting and adjust on chassis with t-nut 4mm. ... Printing with 30% infill For ball bearing type 608ZZ from Ama

With the use of a ball bearing, the z-axis stabilizer will support the top of the threaded rod while printing. Feel free to customize as needed. No extra pieces are required and no tool assembly! ...Just slide the piece onto the railing and you're...

This is a combination of a filament guide and a z-axis stabilizer, without the need of a bearing. It's printed at 100.3% scale and works fine as is. It's abit loose until you attach the screws again. ... The spacers are meant to space the original...

Slimmed it down a bit and made it to fit with the lower triangle (simple) Z-axis stabilizer brace: https://www.thingiverse.com/thing:4968237 I used the upper part from, but had to get extended screws (M5-0.8 x 12mm):...

The Ender 2 has been equipped with a state-of-the-art z-axis stabilizer that incorporates an innovative filament tube design, dubbed the "Ender-plate." This cutting-edge system features a ballgear mechanism that ensures seamless alignment and...

Elegoo neptune 4 z-axis stabilizer was made from the front part. ...This time it is connected both ways.There are two options: m8 and m10.Materials required for m8;4pcs m8x50cm rod screws16pcs m8 nutsMaterials required for m10;4pcs m10x50cm rod...

I needed a Z Axis Stabilizer and a Spool Holder for my Tronxy X1, so I decided to merge these two designs into one device. It works exactly as I envisioned it would. A huge thank you goes out to the original designers of both accessories. ...This...

This is a modified version of the Robo R1 Z axis stabilizer clip created by 1nxtmonster. To prevent movement, I sealed off the end of the hole at the end with a secure fit. ... Original File http://www.thingiverse.com/thing:587583

Hi fellow Printering enthusiasts, Please find below a comprehensive guide that combines the filament guide with a Z-axis stabilizer. I recently came across the "Ender 3 Filament Guide" and used it as inspiration for my first experiments with...

This Thing integrates a Z-axis stabilizer with a filament guide. A 608 bearing is needed to fit the lead screw. There are 3 files, the filament guide, wich is a removable part, and two versions of the anti-woble base; one longer than the...

I needed a Z Axis Stabilizer and a Spool Holder for my Tronxy X1, so I decided to merge these two designs into one unit. The result works exactly as I envisioned it would. A huge thank you goes out to the original designers of both accessories, whose...

This custom designed z-axis stabilizer is specifically crafted for a standard Printrbot Makers Kit 1405 printer. The design fits snugly onto the end of the silver rods without obstructing the Z movement of the printer. For added security, two M3x10...

This is a precision-crafted z-axis stabilizer specifically designed for your Replikeo Prusa i3 Rework printer. I developed it to resolve the frustrating issue of z-axis bounce during prints. The result? A stable printing experience like never before....

I wanted an extended filament guide with a Z axis stabilizer to support my filament runout sensor. Note 1: I am using KaminoKGY's Filament Runout Sensor Mount found at https://www.thingiverse.com/thing:4014649 This is my first published...

Inspired by the Frame Braces, TomExplorador created on Thingiverse (https://www.thingiverse.com/thing:2491003), I designed my own frame braces/z axis stabilizers for my Creality CR-10s S5, the 500x500x500 version. No building space loss occurs on...

For the CTC I3 Pro B Clone, align the z-axis for stability. Attach a mount specifically designed for Bowden-style extruders. To achieve a tight fit, intentionally omit any clearance around the bearing or rod, necessitating sanding or filing to secure...