z axis motor mount 3d models

https://www.thingiverse.com/thing:2972363 Re-Modeled shorter to accommodate E3D hotend modification. ... Uses existing holes and screws for mounting. ...

A mount for the power supply. sits on the stock side but further back. Made in two pieces to fit on a ender 3 pro. ...

This is a simple remix to swap the mount to the other side, and lengthen the x-distance to accommodate a larger fan on my setup.

A replacement lower mount that supports the ball screw can be easily 3D printed on a Moonray machine without needing any additional structural supports.

A replacement lower mount to support the ball screw can easily be 3D printed on a Moonray S printer without requiring any additional supports.

Updated mount now seamlessly links to Raffosan's customized setup, boasting an impressive array of enhanced camera options and strategic angles for optimal visual capture.

I upgraded the Y-axis stepper motor to a 48mm length NEMA 17 stepper motor due to limited space between the original mount and extruder carriage. I drew inspiration from acefx's design (http://www.thingiverse.com/thing:1352183) to create an updated...

I designed this mount for NoIR camera case (small distance version). This mount for Ender 3 V2 points the camera to the bed. ...I am using wide angle IR camera.

... to better fit the MK3 and MK3S. The part has also been stiffened up. Mount screw included. Print instructionsFilament: Prusament ASA - Prusa Orange Layer Height: .20 - Quality Infill: 40% Supports: From bed only Picture attached of bed position

This is an upgraded MK2 model, engineered with a tailored mounting arm and top design to seamlessly integrate with the MK3 and MK3S. Additionally, the component's structural integrity has been significantly enhanced through reinforcement. ...A secure...

... steps to ensure a secure fit by attaching it to the printer using a zip tie. UPDATE: After further testing, I discovered that the top ear of the original design interferes with Z-calibration, so I removed it and replaced it with an alternative.

This was designed for Prusa i3 MK3 and for Microsoft LifeCam HD-3000, but it may fit the Prusa MK2 too I guess. Also, you may be able to attach any camera to it if it is secured with some zip ties. Although it is a snap-on design I secured it to the...

https://www.thingiverse.com/thing:2393178 This combination of @tomfrayers dual inverted z motor mount and the R_base bracket by @thingirob was built using 123D Design and Meshmixer for construction, resulting in a very fast creation that can be...

And to replace the poor original motor, I bought a 52mm 500W spindle.\r\n\r\nI found a piece here (on Thingiverse) that was supposed to hold this spindle but after printing it out, I discovered that the linear guides spacing was off by 2mm compared...

I liked this mount, but I switched from the Logitech 9000 (which doesn't focus at close distances) to a manually-focused Arducam. ... A M3-.50 nut is required.

The two small screws are reused from removing the flexible base from the camera, and I used one random screw about 12-16mm long to hold the camera mount onto the clip / Ender 3 mount. Webcam:...

Simple and thin Chain Mount that can use with https://www.thingiverse.com/thing:4329294 so there is enough space for a bigger Fan/Hotend. ... There is a gap to do the X, E-Stepper and the Runout Sensor behind.

You'll need an M3 screw to attach a camera mount to your Da Vinci Jr. That's all you require. ... Print Settings Printer: XYZ Da Vinci Jr Rafts: No Supports: No Resolution: .2 mm Infill: 20%

To solve this issue, I modified the mount to have a housing to slide the camera into and remove the issue of anything potentially breaking during installation. ...I have also added a slot in the back of the housing for easy cable management/pass...

To assemble the frame mount, extension(s), and camera mount, use M2,5 x 20 screws/nuts (available at Amazon under B015A338TG). For securing the USB cable, I prefer to use ZIP ties, planning to add some additional lugs in a future update. ... January...

Important items: The center motor axis circle bump is notoriously stiff, so get ready to sand it down. When you add printing support to the M3 nut mounting points, be aware that removal can become a real challenge. ...To avoid this, ensure a wide...

Here's the remix I've done on a motor mount for Prusa i3 Y axis, tailored specifically for 10mm rods. ...A SolidWorks file is included in this package to make it easier for you to customize or modify if needed.

Mounting the y-axis motor for a 3D printer on a T-Slot frame involves several steps. To get started, visit Thingiverse and find the model with ID 2323003, which provides instructions on how to connect it to the frame. ... The default setting is designed...

If necessary, make adjustments to the mounting position or sensor orientation to achieve optimal performance. ... By following these simple steps, you can effectively install a bed level sensor on your Anet A8 3D printer and enjoy more precise prints...

I reworked this Y-axis motor mount after I realized how significant my Y-axis backlash was. This updated mount features an extended front component that enables you to place two additional screws for support. Next, I designed a new rear component...

Human Created A Rapid Mount For The Stock Robo3d's Differential IR Height Sensor To Suit It Better. Revised Files Included, Adding 1.5mm To Enhance Overall Performance As Initially It Was Slightly Insufficient. Print Settings Revealed: Rafts Aren't...

I designed an easy-to-make mount for my eSUN filament dryer, replacing the stock spool holder completely. The new design also eliminates the need for a runout sensor since I don't use it. ...To add some extra visibility, I created a slot to slide in a...

(this gives enough room for the extruder to fully home itself without hitting the camera) - Print as shown in slicer image - You'll need to flip the camera orientation on Octoprint if you want to record video the correct way rather than upside down -...

... already fragile form of the Davinci. ...To sidestep this problem, I modified the mount to utilize the existing pre-existing stock hole instead. ...This clever solution ensures that it still employs all the same hardware as its original design intended.

This is a remix from https://www.thingiverse.com/thing:398515 and https://www.thingiverse.com/thing:3932687 I wanted a mount my Logitech C310 on my gantry but didn't find any mounts that let me do it without disassembling the stock stand on the...