z axis motor mount 3d models

The original Y-axis motor mount of the Mendelmax 1.5 is flawed, as it fails to account for applied forces, causing the motor to shift when tension is exerted on the belt. To rectify this issue, an improved design has been created with V2 featuring a...

... stepper motors. Print that part with Triangular Infill @ 100%. Printable Versions of Mount: Motor Mount (without Dust Cover) Motor Mount w/ Dust Cover (Dust Cover STL Included) Y Axis Sensor Mount M3 spaced or M5 spaced (Applicable to both above)

CTC Dual Y axis motor mount and cover plate enhances the mounting of the motor while providing a clean finishing touch, replacing washers and utilizing original bolts for secure fixing. Please note that this upgrade is compatible with CTC printers...

Parts list: Printed 1 - Upper Mount 1 - Lower Mount 1 - Finger Nut (Optional) Hardware 1 - M4 x 50 hex head bolt, fully threaded. ...(I ended up with a stainless phillips head that I ran a nut up to the head and locked in place) 1 - M4 nut ( plus one...

... a one-of-a-kind 300mm cubed Wilson TS variation of the beloved Prusa I3 design. ...As I gave its Y-axis a thorough revamp, it became crystal clear that a dedicated Y-axis motor mount was long overdue - and behold, I'm pleased to present my handiwork!

The optical endstop Z mod for Creality Ender 2 Pro for better keeping Z-offset (mechanical stock enstop works for me poorly) Uses TCST2103 (RepRap Standard). ...May be it suitable for Ender 3 too (not tested)

This is a Y Axis P3Steel V4.2 MakerGal Motor Mount that secures the motor against bending because of tensioning the Y belt. Print instructionsUnassociated tags: p3steel v4.2 Category: 3D Printer Parts

This mount secures the Y axis motor of the Zonestar P802Q at a slightly reduced height allowing users to utilize an aftermarket carriage plate that lacks a cutout for the motor. ...Aftermarket carriage plates are frequently more substantial, simplifying...

Two parts in my design attach to existing screw mounting holes, nothing super fancy but very functional and I like printing it in black so it blends in and looks like it came from the manufacturer originally. You'll need two 40mm M3 screws (I bought...

After browsing Thingiverse for readily available parts to print, I came across two promising designs: one that required 4 screws and t-nuts to mount, but unfortunately, I didn't have these on hand. Undeterred, I decided to create my own design from...

This attaches to the Z-axis motor mount by replacing the two screws with two M3 screws that are approximately 18mm long. Originally, there was going to be a piece of M3 threaded rod with wing nuts to secure the ball joint in place. The socket itself...

My Version of a Mount for an 18mm Autolevel Sensor, Like LJ18A3-8-Z / BX, for the Flsun Cube. Caution: I Have Not Verified Whether My Holder is Compatible with Standard or Other Belt Holders. The Small Version (S OS or S TS) Should Fit Both Dual...

Pi camera with IR Ender 3S1 Mount. ...See Original design for mount example

Модель для крепления концевика оси Z, без качалки Для установки необходимо повернуть кнопку концевого выключателя, удалить качалку и установить на новом креплении

... may need to dremel the mount for the lead screw slightly and move it over a bit. I also had to adjust the extruder motor and Z-axis motor mount at the top to keep everything aligned. ...After making these adjustments, this design worked perfectly.

Snapfit Y-Axis Motor Cable Chain Mount (FFCP, Dup4) (tool-less) I still haven't found the X-Axis cable chain mount I like but I modeled this recently and it fits very well, without tools. ...Insert an M3 nut and use an M3 bolt to remove the play (about...

This is the left side X-axis plate for my ServoRap printer. ... Print Settings: Printer: Sunhokey Prusa I3 Rafts: Disabled Supports: Disabled Resolution: .2 millimeters Infill: 20 percent density

Changes made from the original: -1mm of clearance added to the motor mount screw holes to allow for adjustments -Mounted using T-nuts (allows this to be used on either side for dual Z setups) -Clearance cutouts for the screws mounting this to the...

This is a cooling mount for the Ender 3 S1 Pro, I though the Y axis motor ran too hot so I created this shroud which lets you attach a 40 mm fan to the back. ...In my case I have powered it using a LM2596 directly from the PSU of the printer, the...

I've taken Shawdreamer's top mounts and given them a makeover by adding a convenient filament guide on the left-hand side of the mount.

To make it more practical, I remixed it using a shorter LM8UU Bearing so I wouldn't lose too much x-axis space. This should only cost me about 4mm on the x-axis compared to the 20mm I was losing with the longer bearings. ... This design is untested and...

------------- The goal here is to mount a Raspberry Pi Camera v2 to the X-Axis motor of the Prusa Research Prusa i3 MK3, allowing the camera to move up the Z axis as printing, which should make for nice time lapse videos and allow a visual of the...

My version of a mount for an 18mm autolevel sensor (like LJ18A3-8-Z / BX) for the Flsun Cube. Caution: is I have not verified whether the holder with the standard (of Flsun) / other (Besides my) belt holders compatible! The small version (S OS or...

These are Raspberry Pi camera mounts for the Ender 3 series of printers

I fitted a tensioner and installed a mounting bracket on the Pi 3.

Bed level sensor mount for anet a8 Category: 3D Printer Accessories

Wyze Camera Mount Underway, Room for Improvement Still Exists. ...Expect Some Fine-Tuning Before Completion.

Depending on which screws you have available you can use the parts for M3x12, M3x16 or M3x18. One important thing to consider: The lower part of the z-adapter has a recess to leave room for one of the screws of the z-slider. ...The part must be...

This Y-axis motor mount for Prusa MK2s printers has been redesigned into two separate pieces, making installation a whole lot simpler. It securely holds both the stepper motor and the essential Y-axis micro-switch "stop" in place. By splitting this...

I wanted a way to use a damper for the X-axis also, so I adapted the original Ender 3 X-axis motor mount plate to accommodate a damper without changing the location of the stepper motor and keeping the pulley in the same place. To install this on...