yiga clan mask

PiDP-11 case extension
prusaprinters

Get some masking tape/blue tape, and tape the two pieces together, possibly also to the PiDP-11 case. Then carefully take out the screws, remove the back cover and addjust a touch of super-glue on the top of each of the tabs. Ideally, try to clamp...

Deluxe Pool Set HO Scale (1:87)
thingiverse

I would suggest tweezers, fine and medium grit sand paper or some fingernail emery boards (your girlfriend, wife, sister, mother, etc., might have a few to spare), a hobby knife, and some masking tape for when you decide to paint it up. Haven't...

Compact Wall Mounted Forstner Bit Holder
prusaprinters

Flexible inserts should simply pop in to place and be flush with the top of the main body.Now, remove the inserts and bits, mask the main body, and generously paint over the recessed size labels on the front surface in a high contrast color. After...

Kneading trough 3D model
cgtrader

You're free to adjust any textures and add entirely new ones by simply leveraging the provided UV Layout maps (these can be saved out in PNG format with an accompanying alpha mask).\n\nWithin the package, you'll find a list of items all equipped with...

Reverb G2 Vive Tracker Mount (Supportless)
thingiverse

I actually placed a small pieces of blue masking tape along the joints on the side that faces the HMD as an extra precaution. Non-printable parts ------------------------- * [Mounting...

Alien Biomass Planet and Interior Low-poly 3D model
cgtrader

The Static Meshes included in the package are as follows: 3 Egg Meshes 3 Egg Sack Meshes 7 Worm variations 2 floor entrails 2 hanging ceiling tendrils 1 Floor mesh with horns 1 Floor mesh with tendrils 1 Floor mesh with teeth 1 Floor Blob 4 Hanging...

reusable cable ties
thingiverse

Print settings I printed with a .4 mm nozzle at .1mm layer height, following my filaments guide lines for nozzle and bed temp, I did however have some trouble with bed adhesion but that was solved with a layer of painters/masking tape. Post...

009 or N gauge Turntable Servo drive 100mm UPDATED
thingiverse

Use grid covers to mask screw heads. Assemble Bridge: Strip approximately thirty millimeters two-point-five millimeter solid copper cable straighten it Using a file or Dremel form shoulder in the wire stepping down to approximately one millimeter...

Skeleton Waveguide Subwoofer Speaker - (Fusion 360 archive included)
prusaprinters

You can use masking tape on the outer surfaces to avoid glue dribbles. ...I recommend clear Gorilla Glue (the slow set stuff, not super glue), or 24hr epoxy resin.</p><p>Use bluetack or gasket material to get a good seal around the driver and your cable...

Penny Weight Fidget Spinners
prusaprinters

I'm not sure how important the layer heights are, but that's what I used for all my prints. Tip: Use 3M General Purpose Masking Tape High Adhesion for maximum adhesion and to eliminate warping. I had always been printing on 3M Scotch-Blue Painters...

Arduino powered Portal Gun - Modification and shopping list
thingiverse

You can use PG-Grip_R.stl and PG-Grip_L.stl from the original Portal Gun Design from Evarate (https://www.thingiverse.com/thing:3579224) I used the following parts: Arcade buttons...

The Worlds Best Nightlight. LED Moon Sign.
prusaprinters

Predrill first. -Hang it by one hook/d-ring from the very top and it will self level when you hang it.If everything is good after this I recommend taking it apart and spraying it with a texture spray paint to mask the layer lines. ...Pictured is...

Tesla Roadster 2020 Low-poly 3D model
cgtrader

2: 2,2260,416 (As rendered in Octane).\n\nAll glass geometry has thickness.\nThe Airfoil is rigged in Cinema 4D to extend and retract.\nAll wheels have proper pivot points and are ready for animation (Cinema 4D/FBX).\nFully unwrapped UV's are...