yeti microphone mount 3d models

This microphone holder attaches to a tripod! It uses the heat-set insert shown below. Enjoy! ... https://www.mcmaster.com/94459A380/

Convert an architect lamp to a microphone arm. You might have to slightly enlarge the model to make a tight fit. ...100,6% recommended for ABS.

I could not find any 1/4-20 threaded microphone holders, so I made my own! It uses a heat-set insert like the one shown below. I hope you like it! ... https://www.mcmaster.com/94459A380/

I designed a hotshoe adapter for my Neewer NW-35 Pro Microphone Stand so that I could store my Zoom H1N recorder on the microphone arm. ...In addition to this model a 11-12mm M3 &nbsp;bolt is used to hold the hotshoe adapter in place.<br><br><br>This is...

DPA 4099 Stand Mount with a 3/8" thread adapter.

This is a wall mount for IKEA SKADIS panel compatible with universal hook of the skadis collection : https://www.thingiverse.com/thing:2853261

This is a very basic Yeti Snowball microphone mount. It's a threaded bolt on a plate that you can mount to some arbitrary thing. I used it to mount my mic on the underside of a shelf above my computer monitor. I printed it with PETG but any...

This Shock Mount attaches to the top of a tripod/mic stand and allow your mic to attach to it via a standard 1/4-20UNC tripod mount. Once mounted, the Shock Mount will drastically reduce all noise that flows through the tripod/mic stand. A good...

GoPro Mount Enables Hands-Free Video Recording of Live Performances from a Unique Perspective. ...Capture High-Quality Footage of Drummers and Musicians in Action with Ease.

... ... I print in PLA so I thickened the mount and widened the holes. It's been hanging for about a week with no issues so I'd say it's strong enough but obviously watch/inspect it. Two stantions and clamps are needed. I used some 3-4mm thick bungie.

...... I print in PLA so I thickened the mount and widened the holes. It's been hanging for about a week with no issues so I'd say it's strong enough but obviously watch/inspect it. Two stantions and clamps are needed. I used some 3-4mm thick bungie.

A replacement for the shock mount inner ring of this cheap mic I bought on Alixpress. ... https://www.aliexpress.com/item/32998355725.html?spm=a2g0o.order_list.0.0.15941802VUmgLF

I picked up an affordable Acer tablet, loaded it with lyric software, and created a custom mount that clips onto my mic stand in seconds. The mic stand measures 15mm in diameter, while the tablet is 68mm wide and a mere 5mm thick. Installation was a...

... as well as the original item. Just disassemble the existing stand mount, replace the broken piece with your new one, and reassemble in reverse order. ... I've printed mine in supertough PLA with 100% infill, and it's been perfect for weeks now.

First I am not a 3D model designer as you will notice :), however I was tired of letting my wireless mic hang from my camera port because the mic company does not provide or have any mounts for it. These mics have to be plugged into an adapter and...

Modified to make pocket deeper to make room for rack mount screw behind mic stud. ... Remixed from CB/Ham Radio Mic Holder Remix II: https://www.printables.com/model/143075-cbham-radio-mic-holder-remix-ii I printed this to hang my Retevis Mic: Ham...

Shock Mount for Aston Starlight Mic: Inspired by Thingiverse Design Version for Aston Origin Available Here: https://www.thingiverse.com/thing:3377783 The Ring Thickness Should Match the Included Mic Holder on Aston Starlight I Had to Sand Mine...

Microphone Cold Shoe Adapter Specifically designed to mount a Rode Wireless Go / Wireless Go II microphone to a microphone body with a 30 inch diameter but can be used to mount any cold shoe device to a microphone. Included F3D file so that you...

This 3D model boasts photorealistic detail and top-notch quality, making it ideal for close-up renders. ...With approximately 86,390 polygons, this model delivers an exceptional level of precision and visual realism.

Microphone

Microphone

... makes the base of each lug wider to make them more solid sideways. Thanks to the original poster who saved me quite some time to remix with his original design as an example and to make me learn what was the standard threads of a microphone stand.

black microphone

black microphone

This is a precise replica of the "Blue Yeti" microphone model, meticulously crafted in Blender. The original blend file showcases basic shaders from Cycles render, providing a solid foundation for this detailed model. ...With an impressive total of...

This is a remix of Dingo42's blue yeti mount using DMCShep's basic gopro mount.

The latest iteration of the microphone shock mount boasts a revamped ring that cleverly leverages the built-in swivel joint on the lamp for effortless positioning. ...Secure it in place with an M3/M4 nut and bolt assembly for rock-solid stability.

Electret microphone for HAM

Like a microphone.

metalik microphone gray black