yes nobutton 3d models

Customized QR code tag using Thingiverse's Customizer app: [http://www.thingiverse.com/apps/customizer/run?thing_id=46884](http://www.thingiverse.com/apps/customizer/run?thing_id=46884) Options used for this tag: - QR code size: 33mm - QR code bottom...

Print Settings Printer: Monster Kossel v1 Rafts: No Supports: Yes Resolution: 0.2, 0.3mm Infill: 15-25% Notes: I sliced with S3D which made supports easy to remove. But any slicer will work if you have the right settings. Make sure to print with at...

I suggest the command strips or similar products to "fasten" the dock in place so the weight of the cables that plug into the dock don't tilt it around too much. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes...

When I do upgrade my machine (or when I get bored) I'll draw up a nicer optimized mount for the 525...unless someone beats me to it :D Introduction to this version: https://www.youtube.com/watch?v=nYEQ5p\_Yi5k Cutting a full sheet with this cutter: ...

The motion of the Slide moves the Hammer via small bosses in the Slide, keeping the Rotor free to turn. The Rotor is the square notch style from the bakewell remix, to which I added a flange on both sides to keep it centered in the Slide. Changed the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

Yes, they are all short and supposed to be 1mm shorter than a whole number. The differences of a few millimeters won't affect a build. Screws and Misc. These are 6mm x 12mm screws in order to connect posts to each other or to the plates. There...

Yes, rafts take a while to print and eat a lot of plastic as well, but so do the ring segments and one single fail or a warped and thereby unusable ring segment wastes even more plastic. Especially when having issues with temperatures in the print...

Yes the right Bong will "try" to function as a swamp cooler, possibly even concentrating the desiccant further, but the primary "heat flow" will be from desiccant solution to air as the temperature gradient is the other way round... I hope! Q & A:...

It has additional holes and mounting pins for easier, more accurate assembly.Performance compared to a “real” violinDespite the pretentious name, it does not pretend to be a high-end violin, even though according to my musician friends' evaluation,...

Forget to thread the filament and you have to unload the filament and start over. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 3 Extended Rafts: No Supports: Yes Resolution: 0.2-0.3 Infill: 30 Notes: It is EXTREMELY important your...

The name came about when asking the 3D printing facebook group for name suggestions (yes i know, never ask the internet for name suggestions!) My two favourite suggestions were the name Steve, and making an accronym name such as JACP; Just Another...

**Retract on layer change** `no -> yes`- Should reduce filament buildup where layer change happens, so seam should be less visible. **Increase Y max Jerk** `0.4 -> 2 (M205 Y2)`- By default X1 has Y jerk set extremely low. Bringing it up to the...

Yes, they have nothing to do with the fusion cannons, but the ship is huge and fun!Enjoy the fusion cannons and turret. ...Feel free to do whatever you want with them.</p><p><i><strong>Designed on...

(it shows up under the images) Yes it was made from hacking and remixing various models with Tinkercad, but some parts were made completely from scratch in Tinkercad (like the entire X-axis). <a...

M3 bolts various sizes M3 square nuts M3 threaded inserts M5 threaded inserts M5 bolts 8, 16, 20 pin ribbon cables 8, 16, 29 pin 2.54mm Socket Header Connector ISP Male Double-spaced Straight needle Curved needle connectors. 12mm opening Switches,...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

Everything should be fully printable and functional, but check back before you print this to see if any panels have been added or if any tweaks have been made.&nbsp;&lt;&lt;&lt; Food Safety &gt;&gt;&gt;Before you ask: Yes, this should be safe. PLA is...

Yes, by printing four optional STL files you can actually increase your Z axis build height by an additional 50mm to a max Z height of 260mm! The extra 50mm Z height is FREE, because you will reuse the two original 370mm linear rods that you removed...

Yes, rafts take a while to print and eat a lot of plastic as well, but so do the ring segments and one single fail or a warped and thereby unusable ring segment wastes even more plastic. Especially when having issues with temperatures in the print...

For the FlipClock device two units of the PCB have been used: one to control hours and minutes flaps, and another one to control weather flaps. Block diagram Layout Subparts MSP430FR2433 MCU INA333 comparators ULN2003A drivers 3D printed...

* Brims: Yes * Perimeters: 3 (makes it watertight and adds extra strengh) Due to the small size of the Prusa MINI+ print bed, I can only print 1, 2 and 4-way planting modules. If you have a larger print bed, you can print any module you want, since...

The images for the eyes are now higher resolution, include a 4cm measure line, as well as a light and dark sclera and will waste less ink.&nbsp;Bill Of Materials (head only)&nbsp;this base (I recommend PETG for printing)a set of printed eyes (see...

This will prompt to overwrite a file, say yes. The config I included overwrites the BlackBelt default one.<br/>This should be fine since most people who can afford a BlackBelt probably aren't making this ;)</p><p>Also worth mentioning is that the...

If you have any other instructions or preferences, please let me know! assistant Yes, that's correct. Thank you for the clarification. Please go ahead and provide the original text you would like me to rewrite. I'm here to assist you with your...

So, during the 2019 Paris Games Week (yes, it's a long time ago ^^), the HandiFabLab asked me to try to find a solution to adapt joysticks, if possible ergonomic ones, onto the directional cross, and here is the solution I proposed.&nbsp;Description...

(cannot be drawn if unit is inside base or Mars Large Vehicle) Disaster - Drawn if a game piece is accidentally hit(yes, if you accidentally bump your astronaut or building it is a "disaster" for that game piece), or if another card makes you.Tokens...

Oh yes, the humans may have forgotten, but Madam Wilumbra has not. In the time before memory Madam Wilumbra was a simple druid enjoying a peaceful existence among the trees, encouraging growth and beauty from every twig she touched. Flowers bloomed...

Based upon the HotEnd and Hero Me setup you are using, you would add a line to the Start GCode in your slicer’s settings: M206 Y-9 ; Y axis offset, your value will be different The Marlin firmware detailed instructions on setting the printer’s Home...

Yes, by printing four optional STL files you can actually increase your Z axis build height by an additional 50mm to a max Z height of 260mm! The extra 50mm Z height is FREE, because you will reuse the two original 370mm linear rods that you removed...