yashica electro 35 battery 3d models

Battery adapter for Yashica Electro 35. Use standard setting, no support needed. ...Just need a strip of nickel to wrap around the small cylinder put them together and you good to go.

This adapter lets you install a commonly available PX23 6 volt battery in a Yashica Electro 35 GSN camera. They originally used a 5.6 v mercury battery. It may fit in other cameras as well. Very simple print, no supports needed. I printed it at...

This is an ingenious converter designed specifically to house 4 LR44 Batteries within a Yashica Electro 35 camera. To activate it, simply strip a copper wire and wrap it snugly around the converter, then carefully insert the batteries inside. You can...

This adapter lets you install a commonly available PX23 6 volt battery in a Yashica Electro 35 GSN camera. They originally used a 5.6 v mercury battery. It may fit in other cameras as well.</p> <p>Very simple print, no supports needed. I printed it...

I've uploaded the completed Yashica Electro 35 camera design to the system after a month of intense work.

Yashica Electro 35 Battery Adapter /Yashica MG-1 (etc etc)After a sucess of previous model (first upload on 5th december 2019), I decide to improve the model by reinforced the adpater.If you have an old camera that uses mercury cell batteries — PX...

Rewind knob for Yashica electro 35 and similar models. Measurements taken from a similar piece by Yashica J. No threading required, uses a tapered stem to snap into position. The model printed in photographs is an earlier version that did not...

A simple lens cap for the Eltro 35, with lanyard hole, print without supports at 15% infill it fits snugly on mine, but due to printer settings slight scaling might be needed.

A simple lens cap for the Eltro 35, with lanyard hole, print without supports at 15% infill it fits snugly on mine, but due to printer settings slight scaling might be needed.

A battery door for a Yashica electro35CC, possible other Yashica electro camera's as well. ... Use a piece of conductive material to be sandwiched between the battery and the camera contact.

This battery adapter is designed for the Yashica TL Electro, enabling it to function despite the ban on mercury batteries. It requires two 675 zinc air hearing aid batteries, along with some washers. The batteries should be placed at the bottom of...

The Ergonomic Grip Designed Specifically for the Yashica Electro 35 GTN/GSN Camera Measures 140 Millimeters in Length and 32 Millimeters in Width, Potentially Suitable for Other Models within the Same Lineup.

Die originale Quecksilber Batterie ist nicht mehr erhältlich. Diese hatte eine SPannung von 2.7V. Der Adapter ist für 2 Stück SR44 Silberoxid Batterien. Diese haben zusammen ca. 3,1V. Die Diode reduziert diese SPannung auf rund 2.7V. Mein Test hat...

The individual is a person without any notable characteristics.

This model works for essentially anything that uses those discontinued mercury batteries, but was designed specifically for the Yashica Electro 35 line of cameras. Some of the battery names/models in question are the PX32, PX450, TR164 (Malory), and...

This model work for essentially anything that uses those discontinued mercury batteries, but was designed specifically for the Yashica Electro 35 line of cameras. Some of the battery names/models in question are the PX32, PX450, TR164 (Malory), &...

For those who need it but don't have a printer, I can print and send it with free shipping worldwide from eBay: https://www.ebay.ie/itm/283700556300?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649 This model works for essentially anything that...

For Those Who Need It and Don't Have a Printer, I Can Print and Send It with Free Shipping Worldwide from Ebay: https://www.ebay.ie/itm/283700556300?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649 This Model Works for Essentially Anything That...

... ...It is designed to go in the same place as the original holder. This is somewhat of a complicated modification since you will need to remove the old battery older and solder this one in (which requires lenghtening the wire to the negative contact).

If you own an outdated camera that relies on mercury cell batteries - PX32, EPX164, PX164A, HM-4N, or 164PX - I've designed a custom adapter that allows you to substitute these obsolete mercury cells with four LR44 batteries, which are no longer...

I misplaced my lens in Manhattan during a spontaneous birthday getaway. Initially, I was frustrated, but then I recalled having access to a 3D printer. Unable to find a suitable lens cover on Thingiverse, I decided to design and share one of my own...

Replacing the Battery Cover on Your Vintage Yashica Minister D Analog Camera is a Piece of Cake.

This is a replacement back mount for a Yashica ML Zoom 35-70. I design based on the original mount, making minor modifications. I've already tested it in my lens and in my camera. It was designed to be a bit thinner than the original, in order to...

This is a replacement back mount for a Yashica ML Zoom 35-70. I design based on the original mount, making minor modifications. I've already tested it in my lens and in my camera. It was designed to be a bit thinner than the original, in order to...

The lens fits securely onto my camera after I give its inner edge a quick touch-up. ...It stays firmly in place without needing any additional support.

I made this adapter for using an SR43SW silver oxide battery in place of the mercury battery for the light meter of Yashica TLRs (and maybe some other cameras with similar battery bays). The adapter has a slot on the bottom (minus) side for inserting...

A Replacement Battery Compartment Cover Designed Specifically for the Popular YASHICA FR II Camera Model. ...The Highly Collectible Yashica FR-II Film SLR Camera Was Manufactured Between 1977 and 1981, Making It a Coveted Item Among Photography...

The Yashica 35 is a timeless camera, as showcased in this 2018 creation. Maya, 3D Coat for PBR texturing, and VRay rendering were utilized to bring it to life. ...Thank you for appreciating the effort!

Descriptionthis is classic camera yashica 35 :) -Maya 2018 -3D Coat PBR Texturing -Vray rendering Thank you for your interest in this model. If you have any questions, please send me a message Have a nice day. ...Thank You...