yakima end cap 3d models

These are caps to go on the ends of a "1 inch" tape measure antenna. Help save eyeballs and protect against the sharp and pokey bits of the antenna. Inspired by Becky Stern's tape measure yagi antenna project. ... Fusion 360 f3d file included.

I'm impressed with the End Cap 2's snug fit, thanks to its small nub that keeps it securely in place after tapping it in. ...This is my first foray into designing custom parts for my printer, and I was surprised by how effortless the process was - a...

I created this cap to fit over the end and stop the drifting spool from falling off. Solved the problem. ...I thought others might find it useful...</p> <p>UPDATE: 1/27/20</p> <p>I added a Chamfer on the edge to help with fitting on the roller.</p> ...

End cap for 22.1mm outer diameter and 18.2mm inner diameter handlebars. Used screw M5 40 mm for hexagon. It is possible and 30 mm, but it will be back to back. You can also use an ordinary goika, but self-locking is better. --- Торцевая...

I cracked my fragile acrylic end cap by cranking down too tightly, so I carefully measured it out and printed a brand new one right away. I had seriously considered upgrading to this awesome model here http://www.thingiverse.com/thing:2078706 but I...

As a result, I created the attached rendition of Campy's obsolete EC-RE024 shifter handle end cap. This slides right in and will replace original lost or broken parts. ...Version 2 was uploaded to provide increased spring clearance for the thumb lever.

This end cap is designed to fit multiple models of dishwashers. Print it upside down on the U-face. Use supports for small areas (try settings for 5 square millimeters or less). Do not use PLA at all. ...I'm not a fan of ABS, but you can try using it if...

I previously constructed a 3D printer featuring 30mm Bosch rails and used the supplied end caps. However, I recently decided to create custom replacements for these components. The initial design was created using Solidworks, but encountered issues...

... To address this issue, I've created an end cap/guide that significantly enhances usability. ...When the small part eventually wears out, you can easily swap it for a new one, ensuring seamless performance throughout your 3D printing experience.

In my case the end cap had broken off. This endcap snaps in place and essentially bends the electrical contacts so they are in contact with the tube. It also holds the tube up and prevents fingers from accidentally touching the electrical contacts. ...

This lens cap is designed for the end of a 0.965-inch astronomical eyepiece, fitting all such eyepieces. Creating it from HDPE offers flexibility; however, its durability remains untested. Additionally, 1.25 and 2-inch sizes are available with a...

An end cap that fits tightly to the maximum. Can of course be provided with felt glides. The advantage of this is that the felt glides can be removed more easily and the table remains in its "original state". Depending on the thickness of the...

If I remember to find the make/model, I'll post it here. The stock end caps are made from a soft plastic (not as soft as TPU) which splits in half due to creep or something. These fit on snugly enough, but could be somewhat troublesome to push on...

Cap for 30*60 metal profile

I also beveled the parts that fit into extrusion but its still a really tight fit. interface of the pegs between end cap and the tray should be reasonably tight but may depend on your print settings. I've added slight bevels to the points touching...

This is a custom end cap designed specifically for the Orion ED80 telescope model, engineered to produce a distinctive "cross" diffraction pattern on bright stars that's ideal for astrophotography. Unlike other telescope designs like my 10-inch...

This new end cap adds tabs that align perfectly with the Pi's mounting holes, securely holding the Pi in its place. I've tested this with both Raspberry Pi 3B and 3B+, but it should work for any Pi that this case works with since the screw mount...

This is a special cover designed specifically to protect the exposed ends of my motorhome's bumper from damage and wear.

Plastic end caps that hold the crossbar on came broken. Coleman only wanted to replace the cot but I didn't want to create more garbage. Thankfully I have a 3d printer. Have used them with the replacement for about 8 nights and so far so good. I...

This particular model has been tested and has not fallen out of my handle while I have lost 2 of the original zuca end caps. I have included two separate models, one as a standard black cap and the other has the riddler logo on it that i used for...

Easy way to turn plastic gutters into a NFT hydroponic system: Attach PLA caps using PVC primer and PVC Cement.\nUtilize Mounting Brackets for downspout channels from http://www.thingiverse.com/thing:1687100\nApply Net pot Blanking plate from...

Made on TinkerCAD (link) A lot of our old player piano rolls, also known as a pianola rolls, were in bad condition, so I was looking for an easy way to make new end caps for them. Common brands for these include Master Touch a.k.a Mastertouch, and...

http://www.thingiverse.com/apps/customizer/run?thing_id=992119 Instructions Using the following options: slot_width is set to 6.2 trapezoid_top_width is adjusted to 5.5 undersize has been reduced by 0.2 corner_rounding is precisely set at 2 holes are...

I designed this alternative to the Yakima Zip-Straps using 3D printing technology. ...The framework was created with PLA plastic, while the insert is made of flexible TPU material, which was printed with a 90% infill density.

My bike shop lost one of the handlebar end caps. So I decided to create some equivalent. This version fits 20mm inner diameter of handlebar.</p> <h3>Print instructions</h3><p><strong>Printer Brand:</strong><br/> Prusa</p>...

Need an end cap for your new CNC Mill, 3D Printer, or Lasersaurus T-Slot aluminum extrusion? With holes or without them? Single wide or double wide? Just take a look at this OpenSCAD model and create one by making a few measurements or checking the...

This is a handlebar end cap for aluminum mountain bike handlebars. (For carbon fibre handlebars, you'd need to modify it for the smaller inner diameter of the bar. For road bars, you'd need to increase the size for the larger inner diameter of the...

SummaryThis is an end cap for a misumi style 30x30 t-slot extrusion.InstructionsThere are two STL files, one with a hole, one without. More importantly, there is an openscad script to create your own. There is a variable at the beginning called...

This is another power supply end cap, originally designed for use with the MPCNC. I adjusted the voltage while the cover was on and displayed the value. The output comes from the three female XT60 plugs located on the lower left. Here are the links...

The end cap with a clip to attach it to the cable when the cable is in use. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20% Filament: Filamentech PETG Blue Category: Mobile Phone