yaesu vr 500 3d models

Re-sized for a Yaesu FT-530. ...Added fillet to the base and closed the hole in the back.

Set of feet for the Yaesu FRG7. Needs 2 x M4x10 and 2 x M4x25 philips screws. ... Design on tinkercad : https://www.tinkercad.com/things/2dMbBCXfwz6

Корпус переходника sma для подключения к радиостанции yaesu антенны от baofeng и других. Переходник универсальный. ...Печатать без поддержек 100 процентное заполнение.

This is a simple Yaesu FT-8900 YSK-8900 faceplate holder, used as part of the separation kit to allow customization with your preferred attachment.

A sleek and simple cradle for the Yaesu FT2D handheld radio. ...Designed to keep your radio secure and stable while minimizing obstructions to controls and audio output.

Visit my website at www.linuxwolfpack.com to access additional details and other models associated with my current project, specifically a 3D model of the Yaesu FH-2.

Using a rechargeable battery of the type 14500 and a spring, I will recover my old and beloved YAESU VX-1. ...A bit of fine sandpaper is necessary.

This is a remake of: https://www.thingiverse.com/thing:1703604 Brand New Design for Wider and Thicker Yaesu FT1XD SHB-13 Belt Clip. ...The original design for the Yaesu FT1D belt clip was not suitable due to its wider and thicker build.

Here's a comprehensive protection system designed specifically for the Transceiver Yaesu FT 817 and 818. Protecting your Transceiver Yaesu FT 817 and 818 is crucial to ensure reliable performance and extend its lifespan. ...The following protection...

A small table stand for the Yaesu FT5-DE/DR handheld radio.Have not tested with earlier models, but should fit FT3D at least. Printing:No special considerations, this should be an easy one to print.

CatKnobz bracket STL file to suit Yaesu FTDX10. ... The knobs sit back a bit but there is ample room for my fat fingers & I can access the tension adjustment under the VFO knob OK.

This is an optional side grip for the Yaesu FT-857 handheld transceiver, utilizing the existing mounting bracket screw holes found on either side of the device's body.

HT Radios have a tendency to fall over when sitting on the desk. ... This stand designed for Yaesu FT3D. ... I added stick-on rubber feet from a hardware store to keep the base from sliding around on a flat surface.

Replacement refers to a specific term associated with the Yaesu FT-100, which is a model of amateur radio transceiver. ...This terminology might be unique or limited to a particular group.

Designed specifically for cables that don't secure with screws on your Yaesu radio. ... Modeled perfectly for use with cables like the Sena SC-A0114 2-Way Radio Cable, featuring a single pin connector.

A small table stand for the Yaesu FT5-DE/DR handheld radio.Have not tested with earlier models, but should fit FT3D at least. Printing:No special considerations, this should be an easy one to print.

stand for yaesu ft-4x radio , this is a fitting for a car mount , but for now only the desktop version , it came out very light so it is best to glue. ... enjoy !

Pack for FNB-21 or FNB18/19 yaesu / vertex bateries, for use it drill holes for 2 copper nails below the contacts of the radio and mount a circuit of lithium bateries (7.2 to 9.6v). ... In the files it's the manual for fth2009.

Here are feet for the Yaesu FT-991A transceiver. I needed a slightly higher angle than the holder which came with the radio could provide. Update: I realized I forgot to mirror one of the feet in the pair file. ...This mistake is corrected in the file...

This cover is designed specifically for the Yaesu FT-991A Transceiver. Printing requires a 25cm wide printbed, similar to that found on the Prusa i3 model. Support structures are not needed. The uploaded version of this design does not include a...

This holder provides a secure fit for the Yaesu microphone, holding it firmly in place with a snug grip. The addition of screw holes allows for easy mounting options virtually anywhere. ...Its uncomplicated design also makes it highly adaptable,...

I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand:...

This is a tripod for the Yaesu ATAS-25 portable HF antenna. It requries a 1/4-20x1 bolt to hold the tripod to the base of the antenna. ... I like to add a washer on the head of the bolt, but it's probably not necessary.

I'm thrilled to share my latest 3D printing triumph with you all - a custom bracket for my trusty Yaesu handmike that I use on the road. ...This sleek design fits perfectly in my car and securely holds the microphone in place just as intended.

A minimalist stand for the Yaesu FT2D radio. ...Helps make the radio, when in the stand, stable.</p> <p>Doesn't obscure any buttons or speaker.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p class="detail-setting...

I recently acquired a Yaesu FT-70Dr radio, which necessitated a sturdy base for support. I already had a stand designed specifically for my Radioddity GD-77, and with some minor adjustments, it proved to be an excellent fit for my Anytone AT-D868uv...

A nice front cover to your Yaesu FT991 or FT991A transceiver. I put some 4mm thickness windows isolating seal to protect the front of the transceiver from the cover. It fits perfectly and it keeps in place thanks to 2 small plastic appendices.

This Yaesu FT2D holder is designed for a charging plate. The lower section can be connected to contacts and a charging cable. Due to the large contact area on the underside, the radio has great tipping safety. I've tried using copper foil as test...

A replacement knob for the Yaesu FT-50R My radio was missing it's knob, so I designed one to replace it. It's designed as a tight fit which meant I had to tweak the horizontal expansion settings to get it to fit on my printer. I ended up going for...

Adapted mbrewha04 1-piece rails (itself adapted from IU1OPK's rails) to fit a Yaesu FT-2980r radio. It omits the middle risers. It's a couple millimeters short of protecting the very back corner parts of the radio, but at this length they can both...