yaesu ft101z 3d models

... latch securely holds the microphone in position. Before attaching the disc to your mic, ensure its height aligns with specifications. For mics up to 4mm (Yaesu, Alinco) models, use the low-disc version; for 5-8mm mics, opt for the standard design.

A custom cradle stand is designed to hold a Yaesu FT-817/818 securely in place. The stand consists of four distinct components. ...To assemble it, tap an M3 or #4-40 UNC thread into each hole on the two side panels and then attach the front and rear...

Modify it online at https://www.tinkercad.com/things/j3fQPdu5PXA Install the Yaesu head mount on the "L" side using 2 screws, then attach a brodit clip to the other side - specifically engineered for my Sharan clip. ...No extra screws or adhesive are...

... one. ...Getting in touch with Yaesu is like finding a needle in a haystack. At least for me. So here is my contribution to Thingiverse. A replacement knob that on my printer prints in under 10 minutes! ... I hope this is useful to someone else.

https://www.thingiverse.com/thing:5248147 Designed off of Geardwn's Yaesu FT-817/8 Digirig Attachment with 1//4-20 Threaded Insert. https://www.thingiverse.com/thing:5248950 This object was made in Tinkercad. ...Edit it online...

Here is a Cover design of FT-81x-BT-DIGI-Adaptor. ... This project is a Design of Bluetooth DIGI Adaptor, which can be mount on the rear panel of Yaesu FT-817/818 Series Transceivers. ... https://github.com/BG6LH/FT-81x-BT-DIGI-Adaptor

... FT8, JT9, JT65, Echolink, WSPR. I think this bracket works with all the interfaces they sell. I use it with the version Digimode-4-Yaesu. I mount the bracket with 2x 3mm countersunk screws. ... Webpage xggcomms: http://www.xggcomms.com

Mounting the Yaesu FT-7900R to a Jetstream JTPS31MA power supply for portable operations requires careful bracket installation. ...Securely fasten the brackets to the radio and power supply using M4x8 screws, ensuring a sturdy and reliable connection...

A straightforward bracket for securing your microphone when not in use; fits both standard and Yaesu mics by slightly widening the gap. Crafted using OpenSCAD, printed with Velleman K8200 printer featuring 3mm PLA. ...Print the bracket upright as...

This upgraded Yaesu FT-817 amateur radio features a replacement knob. To install, first remove the original knob's rubber collar using an Allen wrench and unscrew its set screw. Slide the new crank knob onto the tuning shaft, secure with the set...

... radios, making them easy to position and secure in various situations. ...This clamp can be mounted on either side of the radio, offering flexibility and convenience. Available mounts include: - Retevis RT3/Tytera MD380 stands - Yaesu VX-6 mounts

Bracket for Yaesu FT-857D head unit. Has been tried and printed, may need some fine tuning as its a little tight but will work after "de-burring." Open SCAD file available to change things. ...You need the FT857DNUB.SCAD file to render the model.

Fat finger Spinner Knob for the Yaesu FT-817. ... Probably would work for most applications requiring a 26mm Knob with a 6mm Shaft.Note: Ream out the Shaft Hole for a 6mm press fit, or Ream out to 6.5mm and self-tap the original Set Screw.

This basic box is designed to securely store four batteries for the FT1D, FT2D, and other Yaesu radios. ...The box's dimensions are perfectly suited to accommodate a belt clip that allows you to attach the radio to either the front or side of the box,...

# stl-ft2d_knob Replacement knob for Yaesu FT2D My knob broke so I decided to try to replicate it. Turned out pretty good. Turns out its pretty common for these knobs to break off. ... Heres the link to the source code if you want to modify it:...

This sleeve slips over the standard VFO dial on the Yaesu FT-450D and has a small protrusion to allow for faster tuning. An STL file and a file for Fusion 360 F3D are included. Can only be used for non-commercial purposes. If you have any...

This is a protection frame for the Yaesu FT817/818/ND series of radios, with places for rubber feet and holders for an antenna tuner. Usefull during portable/qrp work. Works with M2.5 screws and washers. ... Only one side is included in the STL, just...

... to hold your handheld radio in your vehicle. ...fits 2008 era f150 dash. will add photos later. includes dash mount, stud, radio holder for Yaesu ft series, gd-77 and baofeng. has holes for adding speaker / mic connections. ...details to follow

Yet Another powerpole anderson adaptor for the yaesu ft-817! But i need to accomodate a standard power connector which is long. It is very robust. Additional components needed: * TS240 connector (Male DC Power Plug Connector Angle 90 degree L...

This sleeve slips over the standard VFO dial on the Yaesu FT-450D and has a small protrusion to allow for faster tuning. An STL file and a file for Fusion 360 F3D are included. Can only be used for non-commercial purposes. If you have any...

... can be edited directly at https://www.tinkercad.com/things/g4G0n3VQqVB. ...The creator drew inspiration from a single holder found on Thingiverse, specifically http://www.thingiverse.com/thing:691940. It serves as a dual rack for two Yaesu microphones.

I needed a mic holder for my yaesu rigs and nothing to screw a standard mic holder to around my desk and I sure wasn't pocking a hole in the radio so I designed a simple mic holder, it probably wont fit every mic out there but it fits my yaesu and...

The Yaesu mic uses a standard CAT6 style connector. I wired two 3.5mm jacks to a CAT6 Keystone connector. Install the 3.5 jacks into the end-plate first. Next, run the CAT6 connecter through the body and install it into the other endplate. I...

This design combines elements from both a Yaesu FT-60 and a Baofeng UV-5R with the clips securely attached. ...While it's still a work in progress, the consistent diameter of the entire structure is an advantage, but it does cause some wobbling when...

The second version has the Yaesu style microphone button. You could use support on the build plate only. There is a countersink for the press fit nut. I use a larger drill bit to clean out the filiment a bit. ... Reuse the original mounting screw.

... 735, 745, 737, 738, 740, 746, 751, 756, 820, 821, and 910 models. ...It is also compatible with the Kenwood TS-50, 120S, 130S, 140, 180, 430S, 440, 450, 570, 680, 790, and 870 radios as well as the Yaesu FT-840, 847, 850, 857, 897, 900, and 920 models.

A "Handy Stand" for HTs is designed to accommodate a variety of handheld transceivers, including the TYT MD-390, Icom ID-51 & 31, and Yaesu VX5GR models. Its versatility makes it adaptable to most hand-held radios, with potential modifications...

... magnets/plate to be installed on the back of the faceplate. There is a finger groove for leverage against the touch screen so it doesn't slide around when you're operating it. (tags) Icom ID-5100a 5100 ID5100 HAM amateur Radio ICOM Yaesu Kenwood

The TM-D710 bracket is a compact and versatile unit designed to expand the capabilities of Yaesu's handheld transceivers. By attaching it to your HT, you can enjoy features such as cross-band repeat functionality, AM receive capability, and 6 meter...

... able to support heavy loads, but could be secured with glue or shims if needed. It was designed for use with the Yaesu FT-7800 remote head mount and one of the many printable RAM mount arms available on thingiverse. ...Let us know if you build one.