yaesu ft 891 3d models
6340 3d models found related to yaesu ft 891.
thingiverse
Yaesu MH-36 microphone cable entry gland restored. ...Needed a new one myself, now sharing with VK2TOB enthusiasts.
thingiverse
Holder for the Yaesu FTM-300 Mic at the recyclebin of the Ford Transit (2009-2013, MK7)
cults3d
This sleeve slips over the standard VFO dial on the Yaesu FT-450D and has a small protrusion to allow for faster tuning. An STL file and a file for Fusion 360 F3D are included. Can only be used for non-commercial purposes. If you have any...
prusaprinters
Fat finger Spinner Knob for the Yaesu FT-817. ... Probably would work for most applications requiring a 26mm Knob with a 6mm Shaft.Note: Ream out the Shaft Hole for a 6mm press fit, or Ream out to 6.5mm and self-tap the original Set Screw.
thingiverse
This upgraded Yaesu FT-817 amateur radio features a replacement knob. To install, first remove the original knob's rubber collar using an Allen wrench and unscrew its set screw. Slide the new crank knob onto the tuning shaft, secure with the set...
thingiverse
A custom cradle stand is designed to hold a Yaesu FT-817/818 securely in place. The stand consists of four distinct components. ...To assemble it, tap an M3 or #4-40 UNC thread into each hole on the two side panels and then attach the front and rear...
thingiverse
This sleeve slips over the standard VFO dial on the Yaesu FT-450D and has a small protrusion to allow for faster tuning. An STL file and a file for Fusion 360 F3D are included. Can only be used for non-commercial purposes. If you have any...
thingiverse
Yet Another powerpole anderson adaptor for the yaesu ft-817! But i need to accomodate a standard power connector which is long. It is very robust. Additional components needed: * TS240 connector (Male DC Power Plug Connector Angle 90 degree L...
thingiverse
Бокс позволяет использовать аккумуляторы 18500 на радиостанциях Yaesu VX-6R / VX-5R / VX-7R.https://www.youtube.com/watch?v=026F-ulQJdw
thingiverse
A custom-designed panel mounting solution for the Yaesu FTM-400 microphone extension features a compact RJ12 female-to-female connector encased in heat-shrink tubing, perfectly suited for installation onto panels measuring precisely 2 millimeters in...
thingiverse
I recently downloaded on Thingiverse the Baofeng UV5R wall mount and liked it. ...So I designed this one in Fusion 360 for the Yaesu FT60. Works great. ...Nice and sturdy.
prusaprinters
I bolted the yaesu 857 faceplate bracket to this printed mount and it worked great. ...I've also add a file that has the standard 1" ram ball in case you opt to mount it with a ram mount system.
cults3d
This is the protection frame for the transceivers Yaesu FT-817 and 818. It keeps the original metallic side attachment for carrying the radio without any risks. Equipped with foldable feet for better handling and transportation. The...
thingiverse
... system. A note of interest: Yaesu also offers a Vertex Standard branded battery for this radio, featuring a distinct belt clip without a hinge or spring. ...Surprisingly, this unique belt clip works even better with the 3D Printed Desktop Stand.
thingiverse
I am a radio amateur and I wanted somewhere to hold my microphone so I designed this for my mic and my desk (my desk is 31 mm thick and my microphone is a yaesu MH-31) you may need to change the thickness of the part that attaches to the desk/shelf...
thingiverse
This was made so a TYT or Yaesu Ham Radio Head Unit could be mounted in the front of the Work Van by the Gear Lever without drilling holes. ... Use the included Template to Check the Van Dash Profile Before Printing the Main Print
thingiverse
You'll require a specifically labeled 14650 LiIon battery, a brief segment of wire, and a BMS module to finish the enclosure for your Yaesu VX1R handheld. ...Under no circumstances should you attempt to charge the battery without first installing the...
thingiverse
This adapter is specifically designed for older Icom, Kenwood, Yaesu radios. The original design had six pins, but this model has been simplified to just four. Interestingly, only two of these pins are needed to provide power to the radio. ...I've...
thingiverse
Additional components needed: - XT60 male - EDC-6 (DC Cable 1.5m, Yaesu / or similar, sometime also listed as: E-DC-6) - Soldering iron/solder - some drops of super glue or epoxy resin to fix the XT60 in place Check the FT817 powerpole projects for...
thingiverse
... the top/bottom parts. Can add rubber feet if want to keep it from moving around on the desk. Credit goes to the following website which has all of the necessary resistor values needed to build: http://www.linuxwolfpack.com/3dmodel_yaesu_fh-2.php
thingiverse
The switch lever on my trusty Yaesu FP-757HP power supply finally gave up after 35 years of faithful service. With no replacement part in sight, I decided to take matters into my own hands and fabricate a new one from scratch. After careful design...
thingiverse
This is a versatile adapter designed specifically for mounting a Yaesu FTM-400 head unit onto a professional-grade ProClip mount available at https://www.proclipusa.com. The package comes equipped with a convenient mic holder. Additionally, it's...
thingiverse
This is a simple Jeep JL 2018+ dash mount for the Yaesu FTM-400XDR head. This will place the radio head lower and more forward than the stock metal bracket that is included. I used double sided foam tape covering the internal flat and the overhang.
thingiverse
This a Yaesu FTM-300 holder designed to fit in small car compartment. My car is a Hyundai Sonata... not much room to fit a mobile installation. This compartment let you hide your mobile radio head while your away. The radio head snap onto the...
thingiverse
I don't like the Yaesu VX-7 knobs - they're too slippery to turn, especially when I'm wearing gloves. (Check out the last photo.) So, I decided to design two new knobs that look just like the ones on my trusty VX-6. (See the photo.) These custom...