yaesu ft 60r lithium battery 3d models

I got fueled by a print I made of someone else's Baofeng battery compartment, and I set out in Tinkercad to create my own 18650 battery compartment for a Yaesu FT-60. This was my first radio, and I couldn't see spending $20-$40 for replacement...

Human: Upgrading the Yaesu FT-727R HF/UHF radio to lithium power using three 18650 batteries, a custom-built lithium charge controller, and an LED voltage gauge for precise monitoring. http://mju.io/yaesu-lithium-conversion/ The chassis fitment...

This is a custom-made lithium battery charger adapter, specifically designed to work with the 18650 battery created for the FT-60r radio. You can find the original design on Thingiverse at https://www.thingiverse.com/thing:3413951. The adapter uses...

Battery replacement cover for the Yaesu FT-817/817ND and probably the FT-818. The published part has no callsign added. ...You can add this on Tinkercad.

This is a remix of very well designed Yaesu FT-4X Battery box from thazlett, https://www.thingiverse.com/thing:4446212 i just add some tollerance and beef it up to be less flexible. Also i lowered the contacts sims to accomodate thin copper tape as...

I use an FT-4x battery clip as a portable charger, relying on its ability to provide contact spaces for the outer contacts on the back of the battery. To achieve this, I employ a lot of solder to make up the missing contacts in the clip. While not...

This is version 2 of a lithium battery charger adapter designed specifically for the 18650 battery I made for the FT-60r, found here: https://www.thingiverse.com/thing:3413951. My previous design had some significant issues - the wires would break...

This is a DIY battery box I designed using freecad, serving as a battery eliminator for my FT-4XE radio.\r\n\r\nWhile it's not yet complete or flawless, the design works flawlessly as intended. The clips securely hold the device in place just like...

Brief project to mod you radio with 18650.

This battery pack is specifically designed for the Yaesu FT-817, utilizing three high-capacity 18650 Li-Ion cells that are individually protected from damage. ...To get up and running, simply swap out the stock battery compartment for a custom...

This case is for Yaesu FT-11R, for 18350 elements. The springs had to be placed at the bottom and this is not a good idea, but in this case it is the only way to make the design of the case as simple as possible. ... ...

Mockup of the FT-60 stock NiMH battery for modification, which will eventually be upgraded to hold two 18650s. Update Alert! ... The 18650 holder has just been completed and is now available on Thingiverse: https://www.thingiverse.com/thing:3413951

This is a replacement battery charger hole cover. ...Can be modified if youre adding an internal sound interface or somethign!

This is a protective cap for a replacement battery charger opening. ...It can be easily customized when installing an internal audio interface or similar feature!

Pack for FNB-21 or FNB18/19 yaesu / vertex bateries, for use it drill holes for 2 copper nails below the contacts of the radio and mount a circuit of lithium bateries (7.2 to 9.6v). ... In the files it's the manual for fth2009.

I made some key changes to accommodate a different fuse holder and add deeper wire channels between the positive and negative battery terminals that get connected for added flexibility. ... I've included a detailed schematic of the wiring and a clear...

3D printed radio holders for the Yaesu FT-70D

Re-sized for a Yaesu FT-530. ...Added fillet to the base and closed the hole in the back.

This is an optional side grip for the Yaesu FT-857 handheld transceiver, utilizing the existing mounting bracket screw holes found on either side of the device's body.

stand for yaesu ft-4x radio , this is a fitting for a car mount , but for now only the desktop version , it came out very light so it is best to glue. ... enjoy !

Here are feet for the Yaesu FT-991A transceiver. I needed a slightly higher angle than the holder which came with the radio could provide. Update: I realized I forgot to mirror one of the feet in the pair file. ...This mistake is corrected in the file...

This cover is designed specifically for the Yaesu FT-991A Transceiver. Printing requires a 25cm wide printbed, similar to that found on the Prusa i3 model. Support structures are not needed. The uploaded version of this design does not include a...

I recently purchased a Yaesu FT-70Dr radio. I wanted a stand for this radio. I have one for my Radioddity GD-77 and with a slight mod works great on my Anytone AT-D868uv. ... Shout out to the creator of the Radioddity GD-77 stand:...

I recently acquired a Yaesu FT-70Dr radio, which necessitated a sturdy base for support. I already had a stand designed specifically for my Radioddity GD-77, and with some minor adjustments, it proved to be an excellent fit for my Anytone AT-D868uv...

A replacement knob for the Yaesu FT-50R My radio was missing it's knob, so I designed one to replace it. It's designed as a tight fit which meant I had to tweak the horizontal expansion settings to get it to fit on my printer. I ended up going for...

Adapted mbrewha04 1-piece rails (itself adapted from IU1OPK's rails) to fit a Yaesu FT-2980r radio. It omits the middle risers. It's a couple millimeters short of protecting the very back corner parts of the radio, but at this length they can both...

I needed a solution to secure my camera housing to my bicycle, so I turned to existing options for inspiration - specifically the numerous GoPro mounts designed for handlebars. ...This led me to design and build a custom GoPro FT-1D mount.

Manopola Di Ricambio Yaesu Ft-7100

Desktop stand for the Yaesu FT-3DE and probably FT-5DE, too (same case ?) with standard battery. ...No special print settings needed, example printed on Anycubic I3 Mega without supports.

Adjusting Your Yaesu FT-840 Transceiver for Optimal Performance