yaesu 8900 3d models

Verification details of the FBX fileFilesBinary FBXSceneNo Unsupported objectsGeometryNo N-gonsNo faceted geometryManifold geometryTextures and MaterialsPBR texturesNo embed texturesSquare TexturesPower of 2 texture sizesAssigned materialsUVsNo UV...

Two-piece side rails crafted specifically for Yaesu FT-857D and FT-857 mobile radios (also compatible with FT-891). These rails can be mounted on both sides of the radio. ... Some signs of warping and delamination in PLA were spotted after just a few...

... giving you complete control over your radio's position. + You won't even need a Yaesu suction mount - it's not required. This project was created using Fusion 360 while I was learning the ropes. ...And rest assured, it works flawlessly for me.

I own a Yaesu FT-7800/7900 radio system installed in my UTV, securely positioned behind the driver's seat with remote control head units. The setup features essential protection measures to prevent dirt and debris from entering the data port and...

Side panels for securing two Yaesu FT-817 and 817ND radios provide protection from front and back impacts. To install, replace side screws with longer ones to accommodate additional weight. ... These panels were engineered with the following screws:...

Needed a Yaesu mic adapter that would fit on this Icom HM-151 holder (https://www.thingiverse.com/thing:2334907) which is a bit wider than some of the other ones you can purchase from retailers. It seems pretty strong when printing flat and I've...

DC Power Connector for Yaesu FT80 and FT747 HF Equipment This simple connector can be used with common or multi-core cables of 3.8mm to 4mm outer thickness, utilizing the copper in the cable to push against the power connector pin on the radio...

The CatTouch control-display for Yaesu radios from Catmeters.com is awesome. But I wanted a case that tucked up under the SP-10 Speaker a little better. This is what I came up with.This design is “screwless”. The Boards just snap into place. Remove...

A custom car mount for the Yaesu FT-70DR radio that delivers exceptional performance so far, free from any rattling noise and boasting excellent stability with effortless access to side controls and ports. Its durability could potentially be enhanced...

This is designed to hold the new style mounting cage that Yaesu is using that allows the radio to be released with a single lever. ...The mounts attach to the cage with 2 M5x16 cap head screws and nuts per side.Recommended print settings are .2mm layers...

This is a custom Remote Head mount for any of the newer Yaesu style remote head mounts where just the one screw in the middle holds the head in place. You will need a slightly longer screw than the factory one as the mounting slot is much thicker...

Protective side rails for Yaesu FT-817/8 Radio. These are a little longer than most to protect any control cables on the rear of the radio.They have slots, that are above and below the radio, along the top and bottom of the rail for attachment of...

I would guess the standard yaesu wall wart plugged into the radio will charge the batteries, although I have not yet tested that. As that's not my use case. It will most definitely not charge in the Yaesu drop in charger. The nickel strip cuts...

This parts are designed to provide a protective shield for the knobs of the Yaesu FT-817 or FT-818, utilizing the stock screws and requiring no adjustments to screw length. You can print the legs separately, which can be easily removed when you...

... get the proper recognition they deserve for their original designs. ____________________ A Yaesu FTM 400 mount for a 2014-2017 Ram 1500 pickup truck. MAKE SURE YOU PRINT IN SOMETHING THAT COULD WITHSTAND HEAT. ... PLA is not good for this print.

The Yaesu FT-3DR comes without a docking station, which you'll need to purchase separately. When you get it, the base is stamped with four metal feet that are supposed to keep it stable on your desk, but they don't work very well. Instead of being...

I used PLA at 0.2 mm Layer height, but you probably can use any Material ### Installation One video says more than a thousand words, so: Thanks K8MRD Thank you KD8YIX: ** Note ** you should check out the youtube channels of these guys. ###...

This is a custom 20mm ball adapter that works seamlessly with my 67 Designs dash mount in my Jeep, perfectly suited for installing the radio controller head of my Yaesu FTM-400XDR VHF/UHF transceiver. Designed specifically to utilize an M5x20 machine...

**This mod may void the warranty.** **Modify your radio at your own RISK!** 1) Not feeling printful? Purchase a kit here: https://forms.gle/EGKaYYa485J8wiMW9 2) Wanna make one by yourself? Go here for details:...

3D printable desk stand for the remote display of a FTM-400 transceiver.    This simple desk stand has various features.    The front is angled for a good viewing angle.   There is a large hole in the back to pass cables through.    A square hold on...

Supports might be required under the V2 knob spinner. ...Used Prusaslicer's Paint-on Supports.Added a new version (V3) that brings the ring closer to the center, avoiding any need for supports that might affect the knurling pattern.

print diagonally on smaller printers, 50% infill

Used M3x12 screws.

Universal Support for FTM-350. FTM-350 universal holder. ... Print Settings: Printer Brand: RepRap Printer: Prusa I3 Hephestos Rafts: Doesn't Matter Supports: Yes Infill: 20 Notes: Turn 180 degrees.

This model was crafted using Tinkercad. ...Modify it instantly at https://www.tinkercad.com/things/e6aKJ7x4tj5

Fits on the side of the FC-30 tuner, uses the original screws with the feet included. Stops your mic from floating around the shack or falling on the floor. Print on the back but use supports for the cavity. You'll need to carefully cut the supports...

I damaged the belt clip on my VX-2R radio, so I decided to fabricate a replacement instead of ordering one. Making one myself gave me control over its design and ensured it would fit perfectly. The new clip isn't as streamlined as the original, but...

3D printable version of my FT-891 protection rails, the product is divided in 2 pieces and can be printed with most of 3D printers. ... If you like it, a professional grade, single piece version made of laser sintered Nylon is available for purchase...

<p>Almost any material will do the job - I've printed mine with DevilDesign Matt PLA</p>

Nice fit did not require supports. Some sanding for smoothness but not required. ...