yaesu 8900 3d models

A small sleeve to protect and support the SMA to BNC adapter for the antenna on the Yaesu FT-70D transciever. Printed with a 0.2mm nozzle in mind, might be possible with a 0.4 mm nozzle as well, i have not tested it.You might want to add a bit of...

I don't like the Yaesu VX-7 knobs - they're too slippery to turn, especially when I'm wearing gloves. (Check out the last photo.) So, I decided to design two new knobs that look just like the ones on my trusty VX-6. (See the photo.) These custom...

I created a microphone clip for my Yaesu FT-857D since I didn't have one available, so I took matters into my own hands and designed one myself! This design should work with any mobile-style radio that has a mounting screw on its side, but it was...

Here is a remix of this stand with no call sign and a Yaesu logo. I had a lot of issues with supports for printing this so got rid of all the out cuts underneath and to be honest, I don't think they are needed for any reason. I also included a...

3D parts that will allow you to remotely mount your Yaesu FT-7100 or FT-7100M VHF/UHF amateur radio head. It may also work fine with similar radios. Hinge bolt is M6. The eight plate bolts are M4. The flat piece has a 10mm hole for mounting to a...

The Yaesu FTM400 VHF/UHF amateur radio transceiver has a separate control head that can be mounted away from the main body of the transceiver. It comes with a sheet metal stand that can be attached to a top surface, but the back of the control head...

A Yaesu dual-band Ham radio remote face mount uses clever design to fit in a Prius's cup holder via a "Cellcup". The radio face and microphone are held in place on the center console with a smartphone-sized insert, mimicking phone dimensions. Drill...

When venturing outdoors into nature, I always bring my trusty Yaesu FT817ND along in my backpack to savor low background noise and listen to distant broadcast stations or fellow ham radio operators on various amateur radio bands. However, I've...

I'm excited to showcase my first "table legs" design, carefully crafted to securely hold my Yaesu FT-817 and its paired LDG Z-817 tuner together in one neat package. With just rubber bands as a temporary holding mechanism, the LDG is perfectly...

I got fueled by a print I made of someone else's Baofeng battery compartment, and I set out in Tinkercad to create my own 18650 battery compartment for a Yaesu FT-60. This was my first radio, and I couldn't see spending $20-$40 for replacement...

Many times I went to retrieve my trusty Yaesu FT-60R from my backpack, only to find that the power/volume knob had been bumped and the battery was running down.Removing the battery is not a great solution as it adds hassle every time you want to use...

Motivation:I got hold of an old portable amateur radio Yaesu FT-290R, that suffered from leaking batteries. This was probably teh reason why the bottom cover, that is situated next to the leaking batteries, was missing.</p><p>So I designed a...

The part is pretty simple, it's just a plate with a mic mount that is secured by the two screws intended for the mounting bracket on the side of the radio.&nbsp;&nbsp;It prints fine without any supports and with 15% infill on my PrusaMini+ with...

The part is pretty simple, it's just a plate with a mic mount that is secured by the two screws intended for the mounting bracket on the side of the radio.  It prints fine without any supports and with 15% infill on my PrusaMini+ with Prusament...

I created this to mount the control head of a Yaesu FTM-6000 to the dash of my 2016 RAM 1500 truck just to the right of the steering column. The mount is angled up at 15 degrees and provides a flat surface with to which I could adhere industrial...

This is a Yaesu FT-891 rig mount for a RAM 1" ball. The added support under the 891 is crucial as the 891 only has one screw mount, making it necessary to prevent the head unit from spinning. Hardware you'll need: 891 Mount - (Qty 1) M5x12 with...

HR Richter mount for Yaesu Handhelds

Support for FT7800 to screw to the wall Print Settings Printer: Hephestos i3 Rafts: No ...

<p>Soporte para la FT7800 para atornillar a la pared/Support for FT7800 to screw to the wall</p> <h3>Print instructions</h3><h3>Category: Electronics Summary</h3> <p>Soporte para la FT7800 para atornillar a la pared/Support for FT7800 to screw to the...

Bracket to mount a CatDisplay232 to the side of the Yaesu FT-991(A) Amateur Radio

A clip allowing to attach a neck strap to your Yaesu FT-817/818. ...A necessity when hunting satellites, quite useful for /p activities too.

Desk Mount for remote head mounting your Yaesu FTM-100-D radio Head. 2 Pieces. Connect them together after printing with small screws and nuts. ...

Customizable RAM Mount Fits Any Faceplate with 1/4 Inch Hole. ...Installed on My Land Rover LR3's Ashtray, Also Uploading Ashtray Mount.

This is the mic receptacle that can be mounted to a smooth surface using double stick tape. ... I made it for my work car since I had lost the mic mount that came with the radio.

Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://thingiverse-apps/customizer/run?thing_id=54024 Using the following options: NotchedShaft = enabled HoleFlatThickness = 1.5 mm HoleDepth =...

Human: Feet for the FT-726R satellite radio. I've been propping the radio on a slight angle using a piece of wood on my desk for years. These new feet will work with many radios from that generation. ... There are standard height legs and longer legs...

This is a twist on the base design with a notch/slot cut on the side so that there is access to the DC port on the radio while in the holder.

Custom leg for VHF transceiver. ...Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: No Supports: No Category: Other

This is a remote head mount for an FT8900, it is shaped to match the head / body shape of the radio and mirrors this for a pleasing aesthetic whilst creating space on the back for a standard AMPS mount plate.