yaesu 8900 3d models

Reliable alternative clip designed specifically for VX-5R devices, adaptable with personalized identification or radio frequency code! Can be quickly printed at full density setting. ...Securely attaches to the radio via a robust M3 screw mechanism.

I printed this from pla .25 layer Hight no supports needed. The sides clip under the strap brackets on the radio , a little adjustment may be necessary but can be set so with a little squeeze on the cover at one side releases the cover quite...

This is a box that houses a meanwell 30 Amp supply with fan, switched power inlet and Anderson powerpoles.

Customized version of https://www.thingiverse.com/thing:5361008 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5361008

This is a replacement battery charger hole cover. ...Can be modified if youre adding an internal sound interface or somethign!

Customized version of https://www.thingiverse.com/thing:1663381Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1663381

Just longer back rails

Customized version of https://www.thingiverse.com/thing:5199940 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5199940

Prints ok with 0.6mm nozzle.Do not use PLA unless it's used indoors. ...I a car window you need to use PETG or better filament to withstand the heat from the sun. The original bracket was screwed on so you needed tool to remove the display from the car...

This creation came to life thanks to Tinkercad's innovative tools. ...You can edit it instantly at https://v1.tinkercad.com/things/5cMymZPxLLg online.

This is a simple protection cap for these great FT817 side rails: https://www.thingiverse.com/thing:4118033

Original would have been perfect if the finger dimple was slightly larger, which this fixes.

This is a revision of one of my project.https://www.thingiverse.com/thing:3014656Simply offering the front mike side for use it as it's desktop mike.You can choiche a left or right versione simply mirroring it.Best printed in PETGGive me a like.Ciao...

I adapted this scenario to accommodate my safeguarded 18650 batteries. ...My batteries are only slightly longer than those utilized in the initial concept.

This project is designed specifically for an Arduino Mega and a 3.5-inch TFT color screen, with the rear panel simply snapping into place. It's based on the version showcased in "Twittv," which can be found by following this link:...

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/bmIWyY6LtqJI used ABS filament, if you use PLA it will bend and not hold the head as it gets very hot in the cabin and things start to distort in the heat. ...Tested...

When I bought this receiver it was missing the panel that runs across the front of the radio with the logo and model number. I designed this to be a replacement. ...

Added an upper riser to both rails

Customized version of https://www.thingiverse.com/thing:5199940 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5199940

Customized version of https://www.thingiverse.com/thing:5199940 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5199940

Customized version of https://www.thingiverse.com/thing:5199940 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5199940

<p>I remixed this case so it could be used with my protected 18650 cells. ...These cells are a few mm longer than the cells used for the original design.</p> Category: Electronics

People usually use FT290 with eight LR14 batteries that weigh about 550 grams, and the original battery holder adds another 170 grams. In comparison, four high-quality 18650 batteries weigh only 160 grams, and my custom battery holder weighs just...

I've always been drawn to the rugged handles found on professional-grade RACK devices. They not only give these devices a robust and imposing appearance but also serve as a protective shield for the front panel, safeguarding against damage that can...

Customized version of https://www.thingiverse.com/thing:5199940 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5199940

This is an easy way to repair encoder that gets loose with time by making an additional support with bearing. You need a small roller bearing 8/10 mm inside/outside (e.g. HK081410 type) which fits into printed piece, and place it instead of original...

This is a protective cap for a replacement battery charger opening. ...It can be easily customized when installing an internal audio interface or similar feature!

This project is designed for effortless home use and safeguarding of the transceiver in both field and domestic settings, featuring a scalable architecture utilizing plug connections dubbed "dovetail." The most recent iteration incorporated...

This is a mount for my FT-7800 remote head I designed to slide between the headliner and upper console in my Tahoe. Should work with other vehicles that have overhead consoles.It has a plate with mounting holes to attach the remote face to.I printed...