xy 2 pro 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht = 7 nut_shaft_distance = 1.5 retainer_ht = 1.5 teeth = 23 no_of_nuts = 1 m3_nut_hex = 1 m3_nut_depth = 3.0 m3_nut_flats = 6.2...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_nut_hex = 1 pulley_t_ht = 7 idler_ht = 0.5 pulley_b_dia = 22 additional_tooth_depth = 1 motor_shaft = 5.8 pulley_b_ht = 7 idler = 0.5...

A personalized version of http://www.thingiverse.com/thing:16627 was created using the Customizer with settings including idler at 0.5, pulley_b_ht at 8, m3_dia as 3.6, additional_tooth_depth of 1, profile set to 5, pulley_b_dia equal to 22, idler_ht...

Adjustable end stop plates are designed to maximize the usable printing area on the Ender 2. To take full advantage of this feature, you'll need to fabricate a custom plate for both the x-axis and y-axis. Cutting a precise M3 thread in the y-plate...

This is a fix for the X axis tensioner on the Tronxy XY-3 Pro V2. The metal bracket that ships with the printer is not long enough to allow adequate belt tensioning and the hole for the pulley is tapped too far to one direction which causes the belt...

Human: Part Cooling Fan Duct for Tronxy XY-2 Pro This fan duct cools prints efficiently from both sides, preventing stringing issues that often occur on the left side of prints. I modified the original design by thinning out the brace wall, allowing...

Remixed z axis stepper motor mount for Ender 3, pro and v2. ...

Is your lead screw wobbling when the gantry moves up and down? Your Z Stepper motor might not be aligned with the leadscrew nut position. This will allow you to move the motor Front/Back and Left/Right to get the shaft in the perfect position. Print...

The carriage mount - 4 pieces M3 x10mm (already mentioned above) The tensioner mount to the carriage - 2xM3 x25mm + 2 nylon-insert locknuts The belt fixation in the tensioner - 2xM3 x16mm + 2 nylon-insert locknuts The pulley mount on the rod - 2x20mm...

Remixed cooling duct for a Tronxy XY-2

End of a Regulated Course for Tronxy XY-2. ... I used an M4 screw and bolt.

Fan for human unit installed and ready to use.

This is a representation of the X-Y axis utilizing the accurate coupling mechanism.

I made some subtle tweaks to the design - kept the overall form intact, but smoothed out the edges and thinned down the walls a notch.

I really liked the simplicity of the MinV2 Ender 3 fan mount by ThijsOudeVrielink but it did not fit my Tronxy XY-2 Pro so I modified it to fit. Bed Level Sensor Bracket must be used in order for X-axis end stop to be triggered. *I use a...

I did a remix of the https://www.thingiverse.com/thing:3027111/remixes The snap-in SD card adapter fitted well for my Tronx XY-2 Pro but my SD Card Adapter is a bit bigger and I wanted the adapter to be roated by 90 degree. So I used the part to...

Since it's hard to find good mods for the base Tronxy XY-2 and since it's based on Ender 3, there are quite a few differences. ... This fan silencer is just mirrored from the original to point backwards.

... you achieve flawless, high-resolution prints every time. The Tronxy XY-2's unique printing characteristics make it an ideal candidate for this cutting-edge solution, elevating your 3D printing experience to new heights of accuracy and reliability.

... XY Assembly by vergienc https://www.thingiverse.com/thing:4390859 I noticed that the Jointer part was 0.5 mm too small for MGN12 rails. ...The mating part has a 2.1 version number, but the Jointer only has one file, this is the missing 2.1 version.

... XY Assembly by vergienc https://www.thingiverse.com/thing:4390859 I noticed that the Jointer part was 0.5 mm too small for MGN12 rails. ...The mating part has a 2.1 version number, but the Jointer only has one file, this is the missing 2.1 version.

2) After some trial and error, it became apparent that the BLTouch probe was not compatible with the Tronxy XY-2; however, the printer worked flawlessly when paired with a PL-08N sensor instead. 3) The original 50x15 fan wing has been updated to a...

The XY-2 mod scene can be tough to navigate, especially when you're looking for top-notch upgrades that make a real difference. Since this printer shares its DNA with the Ender 3, it's no surprise that there are some notable differences between them....

XY joint for 1515 extrusion (replacing the 2020 one) on the X axis, compatible with Voron Trident/2.4 This is a lightweight version of the stock one designed for 1515 extrusion on X axis, mainly reduced thickness, modified the hole size and position...

Just Modded a little for the tronxy-xy2 I have, maybe it works with xy3 and xy2 pro (please comment if it does or does not) ORIGINAL POST: ***Update- I'm re-releasing this under the GPL and including the source files. This last model has a few small...

Just Modded a little for the tronxy-xy2 I have, maybe it works with xy3 and xy2 pro (please comment if it does or does not) ORIGINAL POST: ***Update- I'm re-releasing this under the GPL and including the source files. This last model has a few small...

I don't like that the wire can stick out at least somewhere, so I decided that I need to come up with these plugs for my Voron 2.4 (SIBOOR-Voron-2.4-AUG) for other versions it may not work, well, or you can mirror one of the details. ...To install, you...

... screw. I've tweaked the X endstop so it now hits the X block itself. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Don't worry about it Supports: Yes, definitely Resolution: We're going with 0.08 inches Infill: Solid, 100%

There was some deviation in hole positions, so I drilled 2.5mm holes afterwards and screwed stock screws directly to plastic. Additionally, I added a Fusion360 file for you to modify it if you want. Please note that the hole alignment might not be...

Small two-legged stand for the Arlo Pro that gives it a friendly robot look. The design enables you to mount the included in-pack magnet directly to the print and free-stand your Arlo indoors anywhere without needing any drilling. The design has...

M365 pro 2 parts