xtool d1 z axis extension 3d models

This hold your xTool and u can use the raiser if u want to use a rotary.

These feet are intended to be used the the XTool D1 to keep the engraver locked in the same spot for better registration. Add one foot to opposite corners of the engraver and screw down to the spoil board with #4 x 1/2" Stainless steel flat head...

This adaptor allows you to remove the xTool fan, attach the provided flexible duct directly to the xTool enclosure and then attach that duct to a 150mm extraction fan to increase the extraction air volume and prevent fumes/smells from getting out of...

Pliers for use to remove lens from D1 10W 16mm Laser. ... Print with 100% infill.

I got a new D1 Pro 20W and I have it in an enclosure, but the exhaust can't pull the smoke out fast enough to keep the laser module from pulling smoke in and getting very dirty. I made this to connect a cpap tube and bring in fresh air from outside...

This is a remix originally made from here https://www.thingiverse.com/thing:6143965I believe theirs was based on a D1 Pro 40w adapter while mine is a 20w. ... It was just a bit too small and also found the design to really work on the front of the laser...

You can boost your Z axis support on the SmartrapCore V.1 by snapping two easy extensions into place, increasing its depth by three centimeters along the Y-axis. To do this, simply screw these extension pieces onto the back wall of the box using...

Supports are designed to provide full Z-axis clearance, ensuring smooth operation with direct drive mods and preventing wire rubbing issues. So far, no rigidity problems have been encountered. Printing with six or more perimeters is recommended,...

I wanted my spool holder to sit higher on the Z-Axis rods because of a cable chain installation for the Y-Axis, so I came up with this quick and simple height extender. It provides about 3.4 cm in extra height. This extender works well with most...

That's why I needed the Z axis extension - it saved me about 6 mm of Z-Offset correction instead of 12 mm. The extension fits snugly in place, which is good because I want to make sure it doesn't budge. When you're done with a print, test the max...

Unlike other Z axis extensions on Thingiverse, this kit works seamlessly with the plus model due to its unique guide rod mounting design. Moreover, it is sized to avoid interfering with different Wanhao z brace kits that can be printed. This file...

I have created two extension brackets to be used with the E3D Supervolcano hotend on the Anycubic Chiron. These brackets allow you to reuse your original endstop bracket and just bolt it on to the bottom of the extension. I recommend you bolt the...

I have created two extension brackets to be used with the E3D Supervolcano hotend on the Anycubic Chiron. These brackets allow you to reuse your original endstop bracket and just bolt it on to the bottom of the extension. I recommend you bolt the...

belt clip

Just a 3D printed part for the alignement of the parts you want to engrave/cut. I printed this tool with a raft to avoid a "elephant foot" that can misaligne your pieces. ... If you have any suggestion, please let me know !

... M3 screws about 10-15mm in length to attach the bracket to the base plate. This should make engraving with the XTool RA2 easier and a lot faster, with less down time swapping things around. ...I hope you enjoy the bracket and you find it useful.

Honeycomb Bed Hold Down / Anchor Pins for xTool D1 Pins have two legs for added stability. ... Vertical and Horizontal pins for respective orientation.

Prevents XTOOL D1 cable damage Here’s my take on adding drag chains to the D1. Chains eliminate the risk of burning or tearing wires during laser operation. The engraving area is not affected by this modification. WARNING: Extending stepper motor...

... out for the IR. STL's uploaded: - d1_ir_module_box_top.stl - TOP PART ONLY - d1_ir_module_box_bottom.stl - BOTTOM PART ONLY - d1_ir_module_box_complete.stl - COMPLETE PARTS - d1_ir_module_modified_top.stl - MODIFIED TOP PART ONLY Enjoy! ...=)

Allows the XTool D1 enclosure vent hose to be used with the excellent Magnetic Quick-Disconnect system designed by  Once in a Six Side  

xTool D1 Pro, enclosure 3" to 4" hose connector for fume extractor. These are estimates as the model is in mm, so the actual OD is a little smaller on both as my hoses were exactly 3" and 4" and this needed to fit. ... Feel free to remix hopefully,...

This allows it to be used on the XTool D1 Pro 5W. The hole for the air assist was moved and now aligns perfectly to my laser head. ... You will still need to print the other parts from Vidarh's drag chain here:...

You need new screws (2x M3x35) I also change the smal wals of the "X- holder" , now its printable for me (PETG Carbon) This part now fits perfectly on my XTool D1 Pro 20W. I also design a new cover for the mainboard. Now, i think is better...

This is a centering Jig to align 86 x 54 mm metal business cards with your Xtool D1 Pro 20w laser module. It snuggly wraps around the existing orange protective shield but just loose enough it holds a metal business card up to 2mm thick so you can...

#xTool D1 Pro Mounting Kit I developed this kit to help mount my xTool D1 laser cutter to a sheet of MDF. These parts were designed to work with #8 Truss Head wood screws. The riser corners separate the protective aluminum panel on the bottom from...

About adjustable leg extensions: These threaded extensions screw directly into the D1's legs and extensions, but offer adjustable height. The short version is close to 1.5 of the official leg extensions when collapsed and 2.5 extensions when full...

I have a 400x400 honeycomb but could not find some feet to align it to my xTool D1. So I designed them. I made two versions. >Version 1 - It aligns the honeycomb centered. >Version 2 - It aligns the honeycomb a bit lower to the center. ...

Design d'un Pin's sur contreplaqué de 3mm graver sur xTool D1 10W Fichier Laser lightburn https://drive.google.com/file/d/1KMgJk-9XbXzhC2NGUFRmko58U5NGS1Cz/view?usp=sharing Si vous prenez le fichier svg, il faudra paramétrer les différentes lignes...

2023-11-20 - Updated top plate for better fit.THIS IS A REMIX of two other projects.Rich Newley's Extraction tube/top Plate: https://www.thingiverse.com/thing:5833454SGBE's Top Plate: https://www.thingiverse.com/thing:5530689This is for the 20W XTool...

I am back with one of my next xTool projects. As mentioned in my other post, I thought it would be cool to have different color laser head module top plates for the various devices. This was made in TinkerCAD. Why TC? Because I could and it works...