xtool d1 laser feet and grid 3d models

Shipping containers in standard sizes, both 40 feet and 20 feet, provided with metallic, roughness, diffuse, dust and scratches, and bump maps, the model made to be in used condition, with subtly corroded edges and dents. ...Suitable for artworks...

I designed this to elevate material 10mm above the honeycomb panel to reduce flashback burns. ...The pin is oval shaped 9x10.5mm and fits snugly in my XTool honeycomb panel. ...The material slots are for 3mm and 5mm material.

The creator of this is amazing and I simply fixed the output file so that it loads with the correct scaling. ... To fit in the xTool Honeycomb waist board you need to print it at 250%.

The housing is designed to perfectly house a Wemos D1 Mini V2 and a BME280 breakout module. This sensor can measure temperature, humidity and pressure. The lid is slotted to allow for air ventilation and it slides into the housing. There is a wall...

I therefore decided to create this simple case specifically tailored for the Wemos D1 Mini from version V2.3 and up. This design also accommodates a small sensor, such as the BME280. Update: When running idle loops, the Wemos can become quite hot...

The ESP8266 module is the Wemos D1 Mini V3 PCB, not the one with the ESP8266 in a can in the PCB.Moisture...

The D1 mini clip is from https://www.thingiverse.com/thing:4665495 (the remix form wouldn't find it for some reason). ... The openscad source for the top uses the spline library found at https://github.com/teejaydub/tjw-scad ...

Battery Adapter for Ebike compatible with model d1 and fiido d2 This kit is compatible with the original battery and with a compatible one, the battery model is 10S3P. March 2021 -I've added the plug . ... Please for any further remix link to this...

Case for Wemos D1 with Power Shield and PIR Sensor. I employed the Blynk app to develop a motion sensor using this setup. To prevent false alarms, I used a 1K resistor between the signal pin of the Wemos and the signal pin of the PIR sensor. ...You can...

Adjustable heat bed and glass table holder designed specifically for Micromake D1 users. Corner clips are included to significantly enhance the structural integrity of the Delta printer's frame. For optimal results, it is recommended to print with...

In my case i had a "azdelivery d1 mini" and "BME280". You can change the "airrohr_d1min_sds011" in FreeCAD and "airrohr_bottom_ventilation_bme280" under https://www.tinkercad.com/things/bUd51j9hSom . ... The printersetting is the same as in...

ABS Greg. ...0.2mm. 105/245 C.http://www.blynk.io/Thermometer DHT22 mini ShieldESP8266 WeMos D1 Mini WIFIDouble Socket Dual Base Shield for D1 Mini NodeMCU ESP8266

... device. ...The outer part is rotatable for raising and lowering temperature. ... Firmware:https://github.com/sakisdog/esp-homekit-demo Assembly (EN later, but photos may help):https://eljokosan.wordpress.com/2021/12/26/frissites-homekit-termosztat/

This is a compact setup featuring the WEMOS D1 mini board, equipped with an ESP8266 processor and an SSD1360 OLED screen, packaged in two separate components that are securely fastened together by a single tiny screw. ...The USB port remains externally...

Case for Wemos D1 mini and 433MHz transmitter or receiver, such as the WL101-341 or WL102-341. This case can be used with other sensors as well. ...The design is explained in detail at...

... thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jyyNi93ZCut It is a small casing for a micro-game project using a Wemos D1 Mini board together with a battery charging shield and an oled shield. Category: Electronics

A DIY project box houses a Wemos D1 Mini and soil moisture sensor. An additional hole accommodates the cable of a DS18B20 temperature probe. Power is supplied via CAT5 cable. The ESP8266 module used is the Wemos D1 Mini V3 PCB, featuring an exposed...

This is a housing for Wemos D1 mini to control LEDs

**Full project write up including code here : ** https://gist.github.com/877dev/ab7ed069d8b4cd4e2d8da4fc912b4698 **Hardware ** Wemos D1 Mini ESP8266 https://www.wemos.cc/en/latest/d1/d1_mini.html TFT 2.4 inch...

**Use a Cutter to Remove One of the Supports on the Top Part, Depending on How You Want to Insert Your RFID PCB** LED and Wemos D1 Mini Go in the Bottom Part. **The Picture Shows an Old Version of the Bottom Part, Which I've Since Improved for a...

Summary case for Wemos D1 with Power Shield and PIR Sensor: I designed a motion sensor using the Blynk app. When a false alarm is detected, add a 1K resistor between the signal pin of Wemos and the signal pin of PIR. You can find me on Instagram...

Like the summary says, a really simple (wall-mount) case for ESP8266 D1 mini and a 1.77 inch display.Depending on your printer, you might have to adjust the print size. ...Actually, I found the print to be quite tight with our Mk3s, so scaling it up by...

This versatile stand and holder for the ESP8266 Wemos D1 mini provides secure support for Dupont BLS-01 connectors, preventing accidental disconnection from header pins. By offering additional protection to unshielded headers, this holder...

I use a lot of ESPHome based movement and light sensors within my Home Assistant setup and wanted to come up with the smallest practical design that would house a D1 Mini Clone, AM312 PIR and an LDR for rudimentary light level sensing. This is the...

Used Tasmota and Home assistant integration. Led is One WS2812b and power supply is direct from Wemos D1 mini. Wiring is simple. ...Can be soldered to any digital output pin on D1 mini. Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No...

The brainchild of a micro-game project, this tiny casing is designed to house a Wemos D1 Mini board in perfect harmony with a battery charging shield and an OLED display shield, resulting in a seamless integration that elevates the gaming experience...

This will hold a Wemos D1 Mini, a 128x64 OLED screen, and an AXDL-345 accelerometer inside of the handle. More information on the project at ryansprojects.tech In order for this to thread on to a typical keg handle, you will need to glue a nut...

This box can house a 1604 LCD (16x4 matrix) and a ESP8266 D1 moduleThere are two holes that can be used to mount control buttons - i mounted them on a small piece of breadboard.The rear panel attaches using self tapping screws1604 and ESP8266 mount...

It's a simple build, requiring just a few, cheap and easily sourced parts and a little bit of soldering. I have included the circuit diagram. The code is for the Arduino IDE and based on a combination of a few library examples so it should be easy...

This end effector is specifically designed for the E3D Volcano hotend, and it can be easily modified to accommodate 1.75 mm or 3 mm filament by simply printing a different holder clip. The end effector base also features an 18 mm hole that's perfect...