xtool d1 grid pattern 3d models
96104 3d models found related to xtool d1 grid pattern.
thingiverse
Designed these feet to create an air gap between my Two trees honeycomb and the aluminum sheet below so smoke can escape when cutting wood. Should fit any brand honeycomb that has a thickness of 22mm. ... Orient the piece 90 degrees so you don't need...
thingiverse
A direct replacement for the chuck attachment that comes with the RA2 incase you loose or damage one. Recommended to print solid using a resin printer. Not tested with FDM however it should work if your printer is dialed in. Do not tighten the...
thingiverse
This clamp will raise your materials 5mm above the honeycomb, to help reduce dirt and soot transfer to the underside of your project, and increase airflow.It is designed to be used in conjunction with the S1 magnetic hold-down pins.Stupidly, I forgot...
thingiverse
I designed this as an alternative to the previous version. The main reason being that with a small aperture you needed a powerful extractor fan. ...This version will work with a more limited unit.
thingiverse
This is a small adapter that hooks on the adjustable tail and easily allows you to adjust the level of tapered objects in the rotary adapter. I printed it with ABS but it should work fine with just about any filament. ...Just slide the leg inside the...
thingiverse
This simple little support slides into the grooves on the RA2 and is used to support tumblers using the chuck attachment. With some larger tumblers, the brackets aren't strong enough to hold the tumbler so put this little strap on and give your...
thingiverse
Customized version of https://www.thingiverse.com/thing:3061316 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061316
thingiverse
Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651
thingiverse
Customized version of https://www.thingiverse.com/thing:969819 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=969819
thingiverse
Upload this to lightBurn, position and print. Would recommend using 5mm+ wood. ...I have printed with 20mm oak plywood, 100% power, 6 speed, 6 passes.
thingiverse
Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038
prusaprinters
<p>Been working on pint beer glasses lately and needed something to level the work area. </p><p>Just a simple wedge. </p><p>Printed in tpu to try to keep it from sliding around. </p>
thingiverse
A vertical smoke exhaust adapter to make some space at the backside of the laser.You can use a 100mm flexible pipe for the connection.
prusaprinters
<p>Replacement prisms. Same height just 50,100,150 and 200mm long. ...Tested and work great holds up fine to multiple 10w 100% power cutting jobs. </p>
thingiverse
Pin should slip into honeycomb then twist to lock pin will then have a nice secure friction fit. ...To remove pin twist to unlock and pin should easily pull out of honeycomb.
prusaprinters
I printed this in PLA since it doesn't need to be super rigid, a little compliance is good. Good amount of pressure applied w/ 3 wall loops & 0.4mm nozzle, could do 2 loops if it's a little too stiff.
cults3d
The ventilation grid boasts a broad circular design, measuring 100 units in diameter and showcasing a distinctive ball-like pattern across its flat surface.
thingiverse
This is an adapter to allow you to laser engrave 4" OD tumblers with handles on an xtool rotary. Spaces the cup up so that the handle doesn't hit while engraving. Ambidextrous, fits top and bottom so print 2 for a straight cup or only 1 if you...