xtool d1 camera 3d models

... Sensors: - MH-Z19 co2 sensor - SHT-31 temperature and humidity sensor - Display SSD1306 128x64 TODOs: - improve Wemos D1 fit (required glue now) - improve MicroUSB connector hole - think about influence of Wemos heating on measured temperature

... that you print three or four button pieces together at a time, as this makes the printing process easier. Electrical wiring instructions can be found at https://spiritdude.wordpress.com/2018/02/16/wemos-d1-mini-with-i2c-ssd1306-oled-128x64/.

Simple case for an D1 Mini esp32 version.D1 Mini snaps into position with enough space below and above for soldering, and you'll also have access to the reset button.You'll find one version with a hole in the back and a lightbulb on the cover. ...There...

Used components: - [D1 Mini NodeMcu mit ESP8266-12F WLAN Module für...

I reprogrammed my Z probe for Micromake D1. When calibrating, there's no force required on the limit switch. One wire is all you need to rewire. I achieved a calibration tolerance of 0.01 mm within an 80 mm radius using this method. ...Alternatively,...

This is a Yet another Wemos D1 Mini box to keep it safe from the outer world. ...the Case allows for wires to come out from the GPIO pins and also a small slot to allow better wifi reception from the anntena.

... that was missing the control pad. ...This part seems to be NLA. After a couple of tries, I managed to DLP print one that is functionally good, and aesthetically not too different from original. This pad should fit the Nikon D1, D1h, and D1x models.

Since I didn't like any of the local BL Touch mounts for the Sermoon D1, I made my own. A simple one. ...It prints with supports touching buildplate.Added a version that allows the print head to reach the right rear corner.

Here is a simple design for a DHT22 sensor case that perfectly fits around the Wemos D1 Mini board. I made sure to keep the board's temperature from influencing the sensor readings, which was my top priority. ...Before you start printing, double-check...

I'm designing a custom Wemos D1 Mini Pro case for myself, and I thought I'd share it with you! ... Changes: 0.1 First release (sorry, not my best work) 0.2 Improved design (this is the one I'm using now) How I Made This Case Designed in Fusion 360

Based on Invizy's original design, this modified version lets you utilize headers or pins that can be attached to a Wemos D1 Mini board. ...I plan to employ it on my robot head, given that there's a dot matrix module positioned at the front and I...

I decided to change the entire hotend of my sermoon D1, it is still in testing, but so far it works well, it is somewhat rough but functional, pending cable management, I use https://www.thingiverse.com/thing:6244541and edit it

... empowers users to efficiently cool their radiators while printing is in progress. The system has been optimized specifically for use with Mikromake D1 devices. ...Moreover, auto-leveling capabilities have now been integrated via the microswitch.

Enclosures for Wemos D1 Mini with sensors. Fusion 360 design files enclosed.</p> <p>The pillars of the top is designed to be used as a snap fit, the layer lines of the print acts as locks. ...If that is not enough, you can use 3 mm self tapping screws,...

Update: v1.1 Installed air vents, illuminated the path with an LED opening, and added a reset functionality through a dedicated button press.\r\n\r\nA compact enclosure now houses both a Wemos D1 mini module and a DC power connector rated for 5.5...

Also I bridged the ADDR pin to GND on the module itself.Here is the ESPHome profile I am using:esphome: name: esp8266-lightsensor friendly_name: esp8266-lightsensor esp8266: board: d1_mini logger: api: encryption: key: "ChangeMe" ota: password:...

Simple slide case for wemos d1 mini. Slide Wemos from one side and lock it with a little bit of hot glue or tape. Rails don't cover holes so you can solder cables to it. ...Drill a hole to secure cables like in picture.

Cover for the D1-mini available with cutouts for 1 or 2 LED-connection cables. ... Gasket for two flat cables, for one round cable and optional manual cutout Print gaskets in flexible filament Indoor version see thing:4605015 ...

Minimalistic housing for magnetic mount to your smart meter.Specially designed for holley smart meters an similar.Top and bottem USB C outlets are possible.The allignment of the USB C outlet depends on the phototransistor / led allignment.IR TTL...

The parts used in this project are: https://www.aliexpress.com/item/ESP8266-ESP12-ESP-12-WeMos-D1-Mini-WIFI-Dev-Kit-Development-Board-NodeMCU-Lua/32653918483.html?spm=a2g0s.9042311.0.0.74wAEl...

This model is closely modeled after the original design by Simo Fe, tailored specifically for the Wemos D1 mini platform. A precise representation of the board's layout can be found, with careful attention paid to its accurate dimensions. ...The...

I'm calibrating my Micromake D1 Z probe. When I'm done with calibration, there's no force on the limit switch. It only takes one wire to rewire. I've managed to achieve a calibration tolerance of 0.01 mm within an 80 mm radius using this method.

Massively reinforced to deal with the epic failure in design of the Sermoon D1 printer. ... Mounting screws are deliberately set slightly wide it means the screws will bind in the CR-touch probe and hold it solid, but then when its done measuring you...

... temp sensor. ...its a tight fit but this way it will stay nicely in its place One problem i have encountered is that the D1 mini will heat up the case. This will result in a 2 - 3 degree celsius higher readings. ...(working on a new design to fix this)

This is a cutting-edge 3D design of the innovative Carbonoid D1 Delta printer. To learn more, visit carbonoid.de or explore its open-source code on GitHub at github.com/carbonoid. ...You can also connect with the community on Facebook at...

The dimensions of the housing can be tailored to suit individual needs, but a standard size of 5x7 inches (13x18 cm) provides ample space for the D1 Mini control board while keeping the overall footprint compact. This design also allows for the...

The Extruder is designed specifically for flexible filaments, and it's intended to work seamlessly with the standard extruder parts from the MicroMake D1 Delta printer. To accommodate printers that have trouble with small holes, we've included a body...

The bottom has a single hole for a 12mm LED button to be mounted. There is a cut out in the bottom to allow access to the USB port. The case is screwed closed with 4x countersunk self-tapping screws. Print instructionsUnassociated tags: D1 Mini...

The original model was nearly perfect for my use case, which was to install a Wemos D1 Mini knockoff inside a Mitsubishi mini split in order to add wifi functionality to allow control through Home Assistant (using this guide).The attached project...

Enclosures for Wemos D1 Mini with sensors are now readily available, thanks to the comprehensive Fusion 360 design files that come with them. The top pillars of these enclosures are engineered to snap securely into place, and their layer lines...