xt60 panel mount 3d models

I made this mount to securely fit the XT60 connector and VTX antenna on the back of the quad. The VTX antenna is angled at 35 degrees to have a more horizontal antenna during flight (for best performance the camera angle should be 35 degrees as...

Xt60 mount for zmr250 frame, carefully crafted to allow the connector to be securely glued into place. Complete set of parts for Zmr250 can be found at http://www.thingiverse.com/thing:1736627 and also at http://www.thingiverse.com/thing:1736621,...

This modification replaces the supplied LED mount and support, giving direct access to an XT60 connector at the back of the battery housing. If you prefer the glass fiber version, visit this website:...

... or space constraints. ...This is a simple setup designed to hold a male XT60 and LED's in place. It was crafted specifically for my Micromake D1 after I swapped out the original connector with 10 AWG wire and an XT60 due to reliability concerns.

... the XT60 in place when plugging and unplugging the LiPo, making it slightly tight to insert. Use flat tweezers or a similar tool to gently push the XT60 into position until the lip fully engages. ... Fusion 360 source: https://a360.co/2HnaALb

I've included an extra one without the mount for those who use the PDB with built-in XT60, but still want the convenience of the "nubbin". I'm seriously considering patenting that term. The part is printed in Ninjaflex, which works well, although...

A Sleek Back for Your Tribute Evo - Perfectly Aligned! ...Hold the UFL Axii Securely in Place, Alongside the XT60 Connector and Immortal T Antenna. ... For a Flawless Finish, Opt for a Print with Robust Support and a 25% Infill Rate.

This is a high-capacity XT60 connector paired with a robust 1000UF capacitor holder, specifically designed to meet the needs of the powerful Armattan Badger and agile Marmott quadcopters.

Designed to clamp an XT60 connection for a drone battery. ...Designed to use M2 threaded inserts and bolts for a compression fit to avoid stress on battery connector solder joints.

Simply attach a straw or shrunk hose and you're all set :)\nEngineered specifically for the exquisite Quadrysteria QR200 Frame.\nIt is absolutely crucial to print this holder at slow&fine speeds so that it fits snugly onto the XT60. ...If it doesn't,...

To enhance accessibility, add a DC power socket to your Printrbot; using a 4-pin ATX socket is recommended but, if unavailable, opt for cheap XT60 connectors (65A) available at Sparkfun. For instructions on incorporating this modification, refer to...

This is a replacement back plate designed specifically for the Armattan Rooster quadcopter frame, retaining its original functionality while incorporating an XT60 cutout. The first model is a single-piece part featuring all necessary cutouts and...

It secures an XT60 connector and the Matek Lost Model Beeper module. Printed in TPU material, it has been redesigned to increase space between components for better FPV antenna installation and to accommodate a Wafl's cap cap. ...The latest version...

This is a sleek rear plate holder designed specifically for the DALRC XR215 (V1) frame, engineered to accommodate the XT60 plug with ease. I'm thrilled that the compact design allows me to place it in a convenient location at the back of the setup.

... ...I recently acquired a fantastic ZMR250 Frame in its big version and I needed to find a way to secure the XT60 connector on it. ...I came up with a simple solution: just clamp it down firmly and add an extra layer of security with a cable tie!

Printed in TPU and precision-crafted for a secure press fit on an XT60 connector, which is then reinforced with electrical insulation tape. Strategically drilled holes accommodate 3mm tubing to safeguard receiver antennas from damage. A dedicated...

iFlight XL5 V5.1 XT 60 Mount

ImpulseRC Apex DC Mount Antenna & GPS BN220 Temp 180° Speed 30 Sunlu TPU

This swept forward mount clears tail mount type antennas like crossfire. Bolt center 25. You need a top plate no wider then 37mm to clear plugs. Purpose build for Iflight Chimera7. ... Prints not to be sold in markets or stored !

The XT-60 drone mount features a secure locking mechanism that prevents accidental detachment, giving users peace of mind while their equipment is in operation. With its adjustable arms and robust design, this mount can be easily positioned to...

... to the top plate, but I sought to maximize my range by strategically positioning the antennas. ...To achieve this, I capitalized on the existing slots that allow for effortless zip-tying of the paddles to the mounts, ensuring a snug and secure fit.

It is also a bit easier to print, because I reduced the angle of overhangs.There are different versions of this mount for the 5-Inch and the 3-Inch version of the TBS Source One frame. Please make sure to print the correct size for your...

There are different versions of this mount for the *5-Inch* and the *3-Inch* version of the TBS Source One frame. Please make sure to print the correct size for your quadcopter! The 3MF-files include PrusaSlicer printing settings for TPU...

Dual USB panel I designed for a specific part: https://www.cablecc.com/combo-two-usb-30-male-to-usb-30-female-extension-cable-50cm-with-screw-panel-mount-holes-p-825.html?zenid=146kpptt0u44gv6lnjen002t63

Antenna / XT60 / Ledstrip - Mount

I created this thing to hold that: https://www.amazon.com/bayite-6-5-100V-Display-Multimeter-Voltmeter/dp/B013PKYILS. ...It perfectly fits onto the edge of printers with 8mm frame panels, just like my Anet A8. ...Thanks for checking it out!

This is a thing I made to hold this: https://www.amazon.com/bayite-6-5-100V-Display-Multimeter-Voltmeter/dp/B013PKYILS Fits on the edge of printers with 8mm frame panels like the Anet A8. #Thank you! ...Like and enjoy!

You can order just the XT60 plug mount, or get it together with an RX pocket and an antenna holder. ...Use a common 3mm RC antenna tube for the antenna tubes.

In order to fit the rear xt60/antenna mount, you have to cut off the original one. This can be done simply with a dremel, standard cutoff wheel, and a steady hand. Medium speed, go slow. I can't stand dangling battery connectors, so this cleans it up...

To fit the rear XT60/antenna mount, you'll need to remove the original one by cutting it off using a Dremel tool and a standard cutoff wheel. Move slowly and steadily, keeping the speed at medium. This will get rid of dangling battery connectors and...