xbox controller extender 3d models

I personally prefer to store my Xbox 360 wireless controller separately from its batteries. Leaving them inside can cause slow discharge over time, so I created a dedicated holder for them. This design allows me to keep the batteries organized and...

Here is an Xbox One controller full-color scan from my Eoscan Pro+. Although I don't need the scan to be 100% perfect, I think it's turned out pretty well. It's also a fraction of the original file size, making it easier to upload - approximately 3%....

Gaming just got a whole lot better with this awesome Xbox Controller Stand for Desktop! As a gift to all gamers around the globe, this innovative device is sure to revolutionize your gaming experience. Check out the incredible video review by...

Mount an Xbox one controller under your clutter-free coffee table with just a few simple steps: attach 3M to the underside of any table or surface you like. For more inspiring ideas, check out our social media: Instagram: @3DBrooklyn Facebook: 3D...

Quick and dirty remix of SmithRC's excellent Xbox 360/One controller hanger gets a flat top makeover for under mounting action. Now it can be attached via adhesive to a shelf or desk bottom, acting as a handy controller holder. I highly recommend...

This is a holder for the Xbox 360 wireless controller. I personally don't like to leave the batteries in the controller. I have the feeling they slowly discharge. So I designed a seperate place for the batteries. The bottom plate has a dimension of...

THIS EXACT VERSION HAS NOT BEEN TESTED YET PLEASE PROVIDE FEEDBACK - UPDATE 2017/11/21: Corrected File Upload and Enlarged Slightly - UPDATE 2017/11/21: Corrected Radius An Xbox One Controller Holder Design to Hold a Controller WITHOUT its Cable,...

Remix combo of the following: Xbox one controller holder Mk 2 by Odemon: https://www.thingiverse.com/thing:1674704 and No-need-support Headphone Holder/Stand by hate_support: https://www.thingiverse.com/thing:3068725 I printed Odemon's controller...

This stand was custom made and fitted to an Xbox One controller, so the stand essentially wraps around the controller, holding it more firmly in place. I printed the stand with the logo up and paused the print to swap out the white for black...

This controller holder is specifically designed to work with Xbox One controllers only, as the 360's protruding battery pack prevents it from fitting into this particular design. Additionally, it can also hold a mic or headphones. There are two...

Adapted the cover for Xbox Series. ... Changed paddles for easier printing.

Pinned against the wall, PC, or Xbox – or any upright surface, for that matter!

There are little rings on the ends of the rods so that they don't fall out once the "Main Top Plate.3mf” is on the controller.Step 4)Put the assembled "Main Top Plate.3mf” onto the "Main Bottom Plate.3mf" with the controller in-between, and use M3...

This is my very first model, a stand designed specifically for Xbox One controllers, which also works seamlessly with the Xbox One Elite Controller - though I haven't tested its compatibility with paddles yet. The only difference between the R1 and...

I'm excited to share my second design centered around the upcycling challenge for Esso/My Mini Factory, which showcases four Xbox One Controllers built from two Red Bull cans and an abundance of free time. To bring this project to life, each "Can Cap...

This adapter allows you to securely attach your phone to an original Xbox controller in the memory card slots. To link your phone, cut off the controller cable and connect a USB cable (leave the yellow wire disconnected), then use a Micro-USB OTG...

My 4 year old decided to rip off the stock thumbstick pads on my XBox One controller. I bought some aftermarket ones that didn't fit snug enough, and he did it again, losing them. So I made this and printed a dozen of them. I used NinjaFlex 85A...

Since my xbox controller has paddles underneath and because I didn't really like any of the other designs out there, I designed my own. This design has rest ledges for the edges of the controller so it makes it harder for the controller to slide off....

Controller Operator

The battery cover is remixed from https://www.thingiverse.com/thing:4093750 The project was designed for the Third Generation (2016) of Xbox One controllers but it will probably fit the earlier Xbox One versions too.DetailsThere are two designs...

A wall hanger for an Xbox One controller. It nails to the wall using two 3/32 inch nails that are 2 inches long.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Monoprice</p> <p class="detail-setting printer"><strong>Printer:...

If you're looking to download all four controller paddles, they're on a different post called Xbox One Controller Paddles All 4 Paddles. If you downloaded the original two paddles on their own, here are the other two paddles. I printed this without...

A simple stand without the xbox logo. ...You can print the logo with an another colour and merge it with the stand with a little bit of glue.

A custom-designed thumb-stick for use on an Xbox One gaming console, specifically crafted to be produced through a 3D printing process.

Console Player Controls Device

A little larger to be more stable Added some fillet and rounded some corners too Replaced Xbox logo by the Starfield one This is a remix from ideawizard design (https://www.thingiverse.com/thing:2191646) Thanks !

This is a versatile stand designed specifically for use with the Xbox 360 console. ...It offers two convenient connectivity options - a reliable wired connection or a seamless wireless link, ensuring users can switch between them effortlessly.

Create a holder that accommodates two Xbox 360 gamepads by printing with three shells and an infill level of 5%. ...This material combination ensures stability, although PLA is recommended for a more rigid structure; alternatively, ABS may be utilized.

stand for controller in wall

It fits Xbox Series S, X, and One controllers perfectly. It could fit other controllers too. Print in your favorite color and put stickers on the flat front, or model a raised logo in tinkercad, and position it on the front with a manual color swap...