xacto knife handle 3d models

Thingiverse does not show even a quarter of the prints I've posted:** https://www.prusaprinters.org/social/52549-unicorn-hatmaker/prints This is V2 of my Xacto knife handle, which has some design improvements over the longer V1 handle. Designed to be...

... that would allow you to still use the cap located below however this current model will not accommodate it without some additional modification. https://www.prusaprinters.org/prints/49128-better-better-xacto-blade-holder-cover/comments Enjoy!

I loved the original version, but after about a month of use i broke the little tab that holds the razor in (probably my fault) but now it cant do that ;) beefed up the little thingy and added a hole so you can hang it.

I'm just ordering a few cheap Xacto knives for [a DIY project](https://www.banggood.com/Multifunction-Hand-Graver-Chisel-Hobby-Craft-Carving-Knife-Tools-Kit-Set-p-1317252.html?p=H5151494967462017032&custlinkid=253734 "banggood.com"). The plan is to...

Update 8/18/21 V2.5 is out, which I believe to be even better than the V2: https://www.prusaprinters.org/prints/74193-v25-better-xacto-knife-handleThese handles compensate for an Xacto blade's angle, making the cutting edge parallel with the handle.

Update 8/18/21 V2.5 is out, which I believe to be even better than the V2: https://www.prusaprinters.org/prints/74193-v25-better-xacto-knife-handleUpdate 2/25/21: I changed the design a little bit so that the small part that the blade is pushing...

Ξ A simple hobby blade (#11 Xacto) handle for printers that aren't quite calibrated yet. Ξ • The main idea is to use a scrap piece of filament, screw, nail, or whatever you want to hold the blade in place. The hole is perfect for my blades but if...

I had tried multiple of my own ideas in an attempt to solve a couple issues with my V2 design, but EasyT2022 already remixed a great one! I took his idea and just adapted it to my original model. This model is extremely finicky because of the...

<p>I had tried multiple of my own ideas in an attempt to solve a couple issues with my V2 design, but EasyT2022 on Thingiverse already remixed a great one! I took his idea and just adapted it to my original model.</p><p>I made two versions, with one...

A nice and safe way to hold your xacto knife blades a glue stick and handle

It doesn't appear in search results due to a problem with Thingiverse: https://www.thingiverse.com/thing:4600545 These handles adjust for an Xacto blade's angle, making the cutting edge parallel with the handle. As shown in the second photo, this...

A way to neatly organize your xacto knife blades and safely cover them with a top, also a place to put you xacto knife handle and a glue stick

I sought a solution to store hobby knives safely in my tool bag without constantly worrying about slashing myself whenever I grabbed a tool. Space was left at 40mm from the collet's end for long blades. A standard #11 blade typically measures 24mm in...

A comfortable grip for the standard X-ACTO knife is desperately needed. To achieve this, I designed a solution using Tinkercad. ...Anyone can edit it online at www.tinkercad.com/things/8zNv3G9Pd8t.

An Xacto Knife Holder that I designed in school. 

Fits 8mm diameter xacto knife and 25mm pegboard.Print upright with supports

Xacto knife cap for the smaller handles (8mm diameter) that holds the 11 series blades or small blades. I have the "entrance" to be 8.15mm because that's my machine's tolerance, your results may vary. ... The clear cap behind the black one is the one...

Xacto knife cap for the smaller handles (8mm diameter) that holds the 11 series blades or small blades. I have the "entrance" to be 8.15mm because that's my machine's tolerance, your results may vary. ... The clear cap behind the black one is the one...

The extra-large Xacto knife comes equipped with a cap that fits snugly onto its 11mm diameter grip.

A repost featuring an 8mm Xacto knife-compatible lid is being circulated for crafting enthusiasts to consider.

I misplaced my Xacto knife cover, so I designed and printed a new one as my first model. Although it might be overly intricate, I encountered difficulties when attempting to slim down the profile. Additionally, I discovered that a robust raft is...

Step 4: Hold the back of the cover securely and insert your Xacto knife into the holder. Make sure the blade aligns perfectly with the gap. Step 5: Your custom-made knife cover is complete. Enjoy using it! The ideal fit is achieved when the cover...

The insert of my Xacto knife broke (see photo). First I wanted to buy a new holder, then I decided to print a replacement. The model was quickly made in Fusion 360. I printed it with 0.1 mm resolution and in PETG. Although the M5 thread is...

What you'll need: 8 - 6mmx3mm magnets like these: https://www.amazon.com/TRYMAG-Refrigerator-Multi-Use-Cylinder-Whiteboard/dp/B09MRN2X7L/ref=sr_1_4?crid=1UJPOKL343YSG&keywords=6mm+magnet&qid=1689869142&sprefix=6mm+magnet%2Caps%2C108&sr=8-4 Regular...

The insert of my Xacto knife broke (see photo). First I wanted to buy a new holder, then I decided to print a replacement. The model was quickly made in Fusion 360.<br>I printed it with 0.1 mm resolution and in PETG.<br>Although the M5 thread is...

The built-in solid stub handle provides a secure grip and adds an extra layer of safety, preventing fingers from slipping forward and coming into contact with the sharp edge. Edit: I've added a longer handle version in a separate file, giving users...

I just had to replace my missing Xacto blade cap and that's exactly what I came up with - a simple printout to solve the problem. ... Intended for use at a 0.4mm line thickness, this design features two sturdy walls.

Designed to fit #11 HOBBY / XACTO type blades.***XACTO BRAND SPECIFIC DESIGNS JUST ADDEDBE SURE TO CHECK YOUR BLADE MEASUREMENTS FOR THE PROPER FILES***No supports needed.No hardware needed.Recommend printing at 0.1mm or 0.08mm when using a 0.4mm...

You can securely insert the knife handle into its designated holder, which is conveniently located at the top. A small compartment, known as the little drawer, holds any additional blades that you may need for your project. Printer Settings ...

... to find elsewhere. ...Tollerences are a little tight but you can adjust the size if need be. It fit my old knife in the picture well with a little in & out movement without the blade. ... Printed on a Photon Mono X with Elegoo Standard Clear Red.