x525 quadcopter frame 3d models
110273 3d models found related to x525 quadcopter frame.
thingiverse
Parametric battery support for x525 quadcopter frame. To use with a velcro strap Openscad code is in spanish, sorry for the inconvenience. ...I'd traduce it if needed.
thingiverse
Replacement motor bracket for the X525 v3 quadcopter frame. After crashing my quad, I ripped a motor clean off. The original fiberglass motor bracket ripped completely into two. ...I designed and 3D printed replacements with a couple of hours.
thingiverse
Plug for the end of the arms on an x525 quadcopter frame with a slot that holds a LED. ...Also has the top removed to allow wires into the tube.
thingiverse
To safeguard my KK2 flight controller, I required a protective casing suitable for mounting onto my X525 Quadcopter frame. I opted for PLA printing at 40% infill to enhance durability. The case was mounted on nylon spacers with the KK2, and it...
thingiverse
This Motormount is custom-designed for X525 Quadcopter, as no printable files were available. It serves as a direct substitute for fiberglass motormounts. ...Print it using high infill (e.g., 100%) to ensure sturdiness; each part weighs around 5 grams...
youmagine
Attribution:http://www.thingiverse.com/thing:40475 - Original feethttp://www.thingiverse.com/thing:10541 - pinsFoot for quadcopters made from 13mm square tubing with a predrilled hole on the side of the tubing for mounting a foot. Meant for my...
thingiverse
This is a battery tray designed to house a Venom 20C 3200mAh battery using the standard holes on the bottom of the x525 fiberglass center platform. I made this to keep the battery from sliding in the battery strap and shifting the center of gravity...
thingiverse
This battery tray is specifically designed to fit the HK X525 frame, accommodating a 3300mah 45C 3S Turnigy LiPo battery. ...It's engineered to suit batteries with similar dimensions, preventing your battery from wobbling and slipping out of the Velcro...
thingiverse
It's for an X525 quadcopter frame. You can mount the MultiWii SE board directly to the bottom plate, the dampener is optional. This is my first Thing here, yaay. ...Print Settings Printer Brand: MakerBot ...
prusaprinters
XT60 connector for X525 frame. With source file. Category: R/C Vehicles
thingiverse
A replacement spacer is available for the X525 V3 frame. ...To install it, use an M3 screw and nuts to fasten in place after printing the required instructions.
thingiverse
The replacement landing gear for a X525 quadcopter features an alternative design to the original fiberglass version with springs. This new gear is without springs and requires 8 of them to be installed, using 2 on each arm of the quadcopter. To...
thingiverse
10 cm high, detachable leg for X525 quadcopter. I used the original hardware to install. The base stays on the quad when leg detached. This is a part of my X525 project: APM 2.6 case w. damper Middle accessory plate Battery tray with low voltage...
thingiverse
To enhance my Quadcopter, I designed and attached LED strip supports.
prusaprinters
I created some parts to mount LED strips to my Quadcopter.
thingiverse
Damper plate holes 45mm distance, I made it for X525 quadcopter. Note: needs a bit of trimmming with scalpel at APM/I2C connection - may be upgraded in the future... ...This is a part of my X525 project: X525 detachable leg Middle accessory plate...
thingiverse
This design is for my china made quadcopter frame X525-V3 & a standard CMOS cam - I am sure it can be modified easy to other frames. Cam used: DAL 700TVL (1/4'' CMOS) Look at the instructions for more details. The actual pics (of drone) are an...
thingiverse
Multirotor-quadcopter Centerplate with APM 2.5 holder with shock dumper mount for x525 frame