x stepper 3d models

To make room for my Flex3drive kit, I had to secure my extruder to the X-axis of my Ender 3 printer, but the standard mounting bracket conflicted with my Automatic Bed Leveling (ABL) setup. To resolve this issue, I set it aside temporarily so I could...

This repair part serves to lift the base of a printer's x-stepper when it starts to sag. My printer's left carriage is constructed from PLA and began to warp slightly due to overheating (the voltage was too high), causing the x-axis drive system to...

Bill of Materials 3D printed parts: 1 - Baseplate, XY Table02 2 - X Table Support Leg 2 - Y Table Support Leg 2 - Stationary Stepper Mount, X Table 1 - X Table 1 - Y Tool Holder 1 - Clamp 2 - Gear_18T_24DP_20DPA 1 - MtgBracket 2xULN2003 6 -...

I Spotted a Z-Axis Cover and Was Determined to Repurpose Its Design for a Larger Knob, Incorporating Press-Fit Magnets Similar to Those Used on My Previous Covers. To Begin, I Printed the Adapted Design at a Layer Height of 0.3mm with PLA Filament,...

You will need 2 M4 x 20 screws to mate the halves of the slider together, 4 1/4" x 1" screws to attach the stepper, and 4 M6 x 30-40mm (I don't recall) screws to attach the mount to the table. I used socket head screws for the slider and mill-side...

A versatile clip model for mounting on the backside of an x-axis motor. Secure the wire in place using a zip tie, as detailed information about motor measurements was scarce. I assumed a standard size of 42x42mm for the clip, with rounded edges to...

Stepper Motor NEMA 23 57MM x 76MM

Stepper Motor NEMA 23 57MM x 56MM

My x-axis stepper motor is prone to overheating after a while, reaching temperatures of around 70 degrees Celsius, which is well above safe operating levels, making it inadvisable to touch for extended periods. I've decided to address this issue as...

I created this set because disassembling my MPCNC took an exorbitant amount of time due to the fact that the steppers were hardwired. These plugs enable you to utilize 4-pin connectors (or 5 or 6, or whatever) to wire your steppers. ...The belt guard...

Modified: 1) stepper motor screw-hole distance = 31x31mm (Moons MS17) 2) stepper motor width/height 42.3mm (43mm space) 3) linear rail 20x20mm screw-distance (was 21x20) When printing from ABS, don't forget to set ~99% shrinkage in your slicer do...

X Y Motor mounts for Sapphire Plus, moved to the side about 2mm - 2,25mm, metal mounts are not welded, vibrating and making strage noises due profile was not closed. 2mm longer M4X8mm Hex screws (7,5-8mm Head diameter) have to be used. ... I...

Friction-fit fan mount with air channels and clearance for a 40mm heat sink attached to the end of the Z-axis stepper comes with mounting holes designed specifically for a 40mm fan. Printing it with the mount side facing down is recommended, as...

I created these after installing stepper motor dampeners and discovering how hot the motors were getting without frame contact. Using Noctua fans with their rubber mounting system keeps them cooler, almost silent, and won't be heard over the hot end...

Print profile is in the attached 3MF file and Gcodes, which are for a CR-10 upgraded with a BTT SKR Mini E3 V1.3 with MicroSwiss DD extruder and dual Z stepper using Klipper. Build instructionsSwitch off and unplug your printer just to be...

Link to a new solution (is here.)[https://www.thingiverse.com/thing:4873050] ----------------------------------------------------------------------------------------- This thing is especially for an Ender3 V2 with: - Micro-Swiss Direct-Drive and...

A customized carriage designed specifically for the Titan Aero clone utilizes a pancake stepper configuration. This unique setup allows users to seamlessly integrate original printer and extruder components, including radial fans and sensors, into...

This increases the size of the center ring for the stepper mount to 24mm to allow the bezel of the stepper motor to fit through the hole. *YOU WILL NEED TO USE M3 THREADED HEAT SET INSERTS FOR THE BELT TENSIONER* otherwise there will not be...

I'm building a custom setup for my JG Aurora A5 and I've come across an issue with the stepper motor Bowden 8mm. ...It's a bit too small to fit comfortably inside, as you can see from the picture.

This is a mounting clamp for NEMA 17 steppers tailored for Prusa i3 x-carriage models featuring standard 30mm holes spacing. It's derived from paenian's original stepper mount design (thing #321523), specifically intended for direct drive extruder...

A flexible coupling is utilized in conjunction with a stepper motor, featuring dimensions of 6.35mm by 8mm.

I'm remixing the design of thing 119814 to incorporate an extra heat sink, utilizing small 14x14x8mm units sourced from ALi. ...Additionally, a 40x40mm fan will be integrated, with its base borrowed from thing 2839889.

This part cracked and broke on my Sovol SV01 so I reverse engineered it out of necessity. ...I have since switched to sensorless homing, so it is no longer needed but hopefully somebody out there will be looking for this exact thing and find some use...

This plastic part on my 3D printer became brittle and fractured so I modeled a copy to print out a new one. I think some if not all of Sovol's printers are open source, so there may already be a model of this out in the wild. ...It was a fun exercise...

Remix of https://www.thingiverse.com/thing:119814 for additional heatsink (i use small 14x14x8mm from ali) and 40x40mm fan fan base is from: https://www.thingiverse.com/thing:2839889 (

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Stepper Motor Shaft Coupler: One is designed for an 8mm to 5mm shaft diameter conversion while the other accommodates an 8mm to 6.35mm diameter conversion. ...Each coupler relies on two M3 capscrews and a corresponding nut to securely fasten it onto the...

Hello !I created dust cover for axis X and extruder E stepper motors - it's designed for Prusa Mini+.You can use it with ventilation holes (partially pushed in) or completely pushed into stepper motor hole.My dimensions was on X axis = 9,1 mm and on...

Build Mod Hack 5mm to 8mm Tall CouplerThis is intended to fit a 5mm shaft of a stepper motor that has a D shaft and a 8mm lead screwDimensions:D = 20mmH = 37.5mmPrinting:Nozzle 0.4mmLayer   0.2mmInfill     35% Min.Hardware:Screws...

Custom X-axis motor mount. Shown in part 2 of the video series on an EMCO PC Turn retrofit. ...Part 1 of the video series is linked below.