x plus qidi 3d models

Fan mount for X-Plus main board. "Main board fan mount v3-A4x10-12mm.stl" is for a Noctua NF-A4x10 FLX fan. While a 10mm fan, it is actually 11mm thick, plus 1mm more for the rubber isolators. Drop the voltage from 24V to 12V for the Noctua fan...

... really that easy. Printer: QIDI-Tech x-Plus Resolution: fine (0.2mm) Support: yes / 70° Print temperature: 190°C Bed temperature: 60/50° (first layer / rest of print) I'm excited to share this ruggedized spool roller with the QIDI X-Plus community!

Mount to hold Sunlu filament heater on back of Qidi X-plus, may work with Xmax as well. holds heater so when running long prints with PETG you can keep the filament dry and with as least exposure to moisture as possible. First upload to Thingiverse...

This is an upgraded version of the Qidi 3D X-Plus Spool Roller, crafted by mistertech, where two critical parts are replaced with a more substantial structure. The original files, Spool_Roller_lock_170mm.stl, which held the assembly together, have...

This is an upgraded version of the Qidi X-Plus 3 Carbon Filter that comes with the new models. This may require modifications of the back panel. If you don't currently have the carbon filter installed there is a template and instructions that are...

QIDI X-Plus 2 Dial Indicator Mount using a dial indicator from my local Menard's. Stem size .375". ... ...

Made this spool holder to be able to mount large (300mm) spools to the X-Plus, as the spool holder rods dont't extend long enough to properly support those. May not be the smartest solution, but works for me. Be careful with spools that are fully...

It is a simple way to get filament rolls to turn easy on the QIDI X-Plus. I had problems with the original piece that holds the bearings. They seemed a little thin and I couldn't slide the QIDI spool support rings over them either because it's a...

I had to slightly rework the holes for the ends of the Qidi-Spool-holder-Rod. Print Settings Printer: Qidi X-Plus Rafts: NoSupports: No Resolution: 0.4Infill: 15% Filament: 3DJake EcoPLA Matt Grey Notes: Printed with 0,6mm Nozzle. ...Don't print...

Awesome Very low resistance Spool holder for Qidi Tech X-plus 3d Printer Makes printing TPE and other exotic filaments a little easier, the bearings lowers the resistance when pulling from the spool. Printed 100% infill for my own use, all parts.

After a year of almost daily use, the plug-in connection to the heating bed of my Qidi X-Plus said goodbye without comment. See photo. Fortunately, the power of my ancient Weller soldering station was sufficient to solder the pin strip back on...

I recently got my Qidi X-Plus and decided to use the internal spool holder to print some ABS. Unfortunately, the new cardboard spool filament holders offered by many filament makers fall off of the back of the spool holder and get caught between the...

I recently got my Qidi X-Plus and decided to use the internal spool holder to print some ABS. Unfortunately, the new cardboard spool filament holders offered by many filament makers fall off of the back of the spool holder and get caught between the...

This is a little modification for original X-Plus Extruder Fan. ...Print this model then replace from two stand-off to this fan duct.

Any filament should work but would use something more temperature tolerant than pla. ... Might have to clean up surfaces to get magnets to sit perfectly level with build plate.  18 are needed for the x-plus build plate.

this are qidi original hot end carriage what i got from email when contacting Linda. ... Im share this becomes before I can found any in internet, now you can have it and if want, can make own mods.

Revised the dimensions, to move the spool closer to the X-Plus top cover. Printed this from ABS (base) and PETG (rollers). 608 bearings fit perfectly. ...The holder is very robust and much more convenient to use compared to the original.

the white 5050 LED strip in the front of the X-PLUS doesn't really show you what is happening at the nozzle. Is ok for gneral viewing.. The LED strip can be cut into 3 sections, and connected with extension wires if you want to put them in a few...

Qidi tech X Plus - top cover closing plate - with thermometer hole, with filament hole or just blank. ... As thermometer used Afriso 63826K - 0-60 grad

Designed to help assist with bed leveling for Qidi Tech. ...X-Plus. Squares are large format 50x50mm and printable area is 250x180 mm. ... Designed to be printed on a single layer with a .04mm nozzle at .02mm layer height.

Designed to help test bed level settings on Qidi Tech X-Plus. 3 rows of 50x50 mm squares to show where adjustments are required. Designed to be printed with a .04mm nozzle at .02mm layer height. ... Printable area is set to 250 x 180 mm

I designed this spool roller to clip onto my QIDI X-PLUS printer, where it replaces a built-in holder that I found created too much friction, especially when printing with TPU material, which caused frustrating voids. To solve this issue, I opted for...

I designed this remix to feature an adjustable spool guide system. To achieve this, I separated the ball bearing axles into distinct parts because the original pivots were excessively fragile. The new pivots can be printed with a 100% infill for...

Filament guide to use with the spool mod found here: https://www.thingiverse.com/thing:4040807 I used the rollers provided here: https://www.thingiverse.com/thing:3854517 Printed in PLA with support, but used support blockers EVERYWHERE...

My simple design to cover the filament hole of the top acrylic cover of Qidi X-Plus and Qidi X-Max when using inner filament holder. No supports needed if you print narrow side up. If you print sides facing the bed, then a basic support is...

The extra blocks are added to snugly fit the QIDI V3 X-PLUS carriage (into the 4mm inset) Print as per Original DRAKEN Duct for HumeBeam. ... I used 6 walls and top/bottom layers, 40% Line infill, Support Everywhere for 85deg (CURA), 40% Zigzag...

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

After getting frustrated with every adapter and modification I've tried for my Qidi X-Plus, and X-Max, I have tried most of the prints and only found one mod that works (yet motion isn't as smooth as I'd...

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...