x plus qidi 3d

QIDI 3D X-MAX holder for spool. ...Required bearing ABEC 5 (6, 7)

The extra blocks are added to snugly fit the QIDI V3 X-PLUS carriage (into the 4mm inset) Print as per Original DRAKEN Duct for HumeBeam. ... I used 6 walls and top/bottom layers, 40% Line infill, Support Everywhere for 85deg (CURA), 40% Zigzag...

Русский У меня сломался шкив мотора оси X на Qidi X-Max. Производитель принтера пришлет шкив только через две недели. Пока сделал свой. Спасибо за помощь мистеру ddddiii...

Filament guide to use with the spool mod found here: https://www.thingiverse.com/thing:4040807 I used the rollers provided here: https://www.thingiverse.com/thing:3854517 Printed in PLA with support, but used support blockers EVERYWHERE...

I designed this remix to feature an adjustable spool guide system. To achieve this, I separated the ball bearing axles into distinct parts because the original pivots were excessively fragile. The new pivots can be printed with a 100% infill for...

... I came up with a clip that keeps the spool of filament centered near the input tube (for the outside filament rack) while still coming off easily for filament replacement. ...Replace one of the QIDI black rings with a clip or both rings with 2 clips.

My simple design to cover the filament hole of the top acrylic cover of Qidi X-Plus and Qidi X-Max when using inner filament holder. No supports needed if you print narrow side up. If you print sides facing the bed, then a basic support is...

for the Qidi plus. ... 608-2RS Ball Bearing you would need on sides.

To setup a CURA Profile for your QIDI X-Max, download the X-Max.3mf and open in CURA as a project. Please save the attached file to your USB drive, do not put them in the folder. Then proceed with the instructions below to update: 1. Power off...

Bowden tube connector for use on Qidi X-Max printer (and possibly X-Plus). The original design this was remixed from would hit the housing when the machine was homing and I wanted to add the push-connect fitting to secure the Bowden tube so I...

--------------------------------------- Main benefits: --------------------- * Reduce the tendency of flex filament tangling inside extruder * Print flex filaments faster * Print flex filaments with more mm^3 flow rate...

It's just a minor fix as some have reported it hitting the motor, 1.4 is a bit thinner so it should clear.Description:Gripen is a high flow fan duct for the QIDI Tech X-Max, X-Plus and I-Mate. In order for you to use it, you need the new extruder...

AboutThis is a Bowden Tube Connector for the QIDI X-Max, X-Plus and I-Mate (S) printhead covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same...

AboutDraken is a high flow dual channel fan duct for the QIDI Tech X-Max, X-Plus and I-Mate (S). In order for you to use it, you need the new extruder carriage. If you don't have it installed in your printer already, you can contact QIDI support and...

Update October 9, 2021Design updated to fit the newer carriages as well as the old with the small 30 mm fan.DescriptionThis is an alternative to my QIDI X-Max X-Plus I-Mate (S) Advanced Extruder Cover.It has similar functions and features an upgraded...

Icarus 2 is a strong, lightweight and dimensionally accurate one-piece carriage for the QIDI X-Max, X-Plus and I-Mate (and I-Mate S) that was designed focusing on strength and ease of maintenance while keeping it very lightweight.Icarus 2 is based on...

This should also increase performance a little.Two new versions without dial indicator holder for those who don't use them.Increased the diameter of the limit switch plate a little (the one in front of the blower / turbo fan).AboutThis is an advanced...

... this design, as PLA will snap in the latch area. Printer settings using an X-Plus: -50% Grid infill -4 perimeters/walls -your choice of support Vent Fan: https://www.amazon.com/gp/product/B00G059G86/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

This is a filament runout sensor housing for the QIDI runout sensor. Placement on XMAX is far from ideal. This moves it to the top cover for a better feed angle.</p><p>Disassemble the sensor casing (torx screws I believe) and place it in the housing....

This is a remix of humebeam's great cover for the hole in the lid of the X-Plus and X-Max. I already had 3 inch flexible duct and 80 mm fans on hand so I remixed it to work with those. It could probably be more efficient in terms of airflow, but I'm...

It uses a M3 x 10mm cap head screw. The belt tensioner is remixed from www.thingiverse.com/thing:1780636 and added into the carriage design. See the original thing, https://www.thingiverse.com/thing:3994628 for all the details necessary to use...

It uses a M3 x 10mm cap head screw. The belt tensioner is remixed from www.thingiverse.com/thing:1780636 (http://www.thingiverse.com/thing:1780636) and added into the carriage design. See the original thing for all the details necessary to use this...

A detailed guide to upgrading your 3D printer with various components and tools! ...Here's a summary of the key points: **M3 Threaded Inserts** * Use Inteq 3mm M3-0.5 Brass Threaded Metal Heat Set Screw Inserts (available on eBay) * Holes in prints...

For the original printhead with 40mm fan. I swapped the very loud fan for a much quieter one. In order to ensure sufficient airflow for cooling, I use these two parts. So far no problems. ... You need 2x M3x30 screws A 40x40x20 fan also fits...

<p>to have the write friction please print with 4 walls 50% infill petg or abs.</p><p>please use support, you can remove them with the help of a cutter</p>

This tiny fan cover allows you to remove the big housing cover of the extruder while keeping the endstop working.By that you save some weight on the printhead, airflow is improved and troubleshooting ist easier.Should work on Qidi i-Mate S, Qidi...

These parts provide the option of using the drybox that comes with the Qidi X-Plus-3 printer, or using a standard-style spool holder. The spool holder may (probably) fit the X-Max-3, but that was not tested. Printable in any stiff material. Test...

I wanted to add the Phaetus Dragonfly BMO to my Qidi X-Plus 2 printer. The mounts on the High-temp dual gear extruder are an exact fit for the Dragon, but the Dragonfly mounting holes come in a 24 degree angle. So I made a modified part for easy...

The design files and instructions have been moved: Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6 Update August 19, 2021 I've added a new file to print. It's a PTFE cutting jig so you can easily cut the exact length required...

The design files and instructions have been moved: Icarus - QIDI X-Plus / I-Mate (S) Carriage for Orbiter 1.5 & Dragon / Mosquito Update November 24, 2021 New belt tensioner: The new Icarus belt tensioner for open belts has been tested now for a few...