x max 3d printer

This piece fits snugly at the entrance of the printer cover's upper portion. ...It should effectively resolve issues related to filament snagging, as well as enhance the process by which the filament is directed into the extruder, thus eliminating the...

Drill a fresh hole, precisely 10mm away from the edge, centered perfectly. Next, insert a nut into the newly drilled hole. Now, drive a 35mm long bolt through the nut with a washer to secure it tightly. Following that, thread an M3 bolt and nut...

This design was created using the online tool Tinkercad, and users can make edits directly on the site by visiting https://www.tinkercad.com/things/6IsUmkGvDzp.

This is a mock-up of Apple's exact sizes on website for the new iPhone XS Max. Print to see how it'll work in your pocket, purse, on wireless charger base, etc. English "STL" output. ...In CURA, print at 2540%.

-Qidi X-Max -Qidi X-Plus ________________________________________________________________________ Since I don't feel like always ordering the PTFE hose from QIDI, I have now designed this easy way to cut your own PTFE hose. With the following...

You will not be able to use the top hat with large spools. The xtensions should sit with a tight fit in the original holders. The mod worked for me as a quick intermediate solution until I finished my piggyback- spool holder. Print Settings Printer:...

It also fits stock printers of course.It should also fit QIDI X-Plus and I-Mate (and I-Mate S) but I've only tested it on my X-Max.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes...

Qidi X-Max (X-Pro) ribbon cables are easy to replace when using these clips to manage the cable. These clips may work on other Qidi printers as well.There are three kinds of clips:Upper back frame railSide corner frame railBottom side frame railAlso...

This spool holder attaches to the rear of the X-Max printer using two M3-.5 x 16 bolts (and washers) which you can pick up from any hardware store or order online. I'm not certain all X-Max printers have these "mounting" holes, so you should check...

Bob Martin in the Qidi 3D FB group owns an X-Max and says it fits his also, otherwise, there is another pi-cam mount you may want to check out here if you think this one is in the way too much: https://www.thingiverse.com/thing:4347548 I'm using the...

**MOVED TO PRUSA:** https://www.prusaprinters.org/prints/155501-qidi-x-max-x-plus-internal-filament-guide-v2 This internal filament guide set works with X-Max and possibly the X-Plus. It replaces the simple OEM vertical guide with a 4mm ID X 6mm O.D....

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

Thanks :)https://www.paypal.me/humebeamengineeringAboutThis is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM -...

It also touches the X-axis belt.To install simply push in the tabs through the holes on the left side of the extruder cover then push down to secure it (use the lower holes) and route the ribbon cable over it.Print SettingsPrinter: QIDI Tech...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM - Bill of materialsYou need a small round hygrometer...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

It is a phone mount for the Qidi tech X-max and X-plus. You would need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

It is a phone mount for the Qidi tech X-max and X-plus. IMPORTANT: You will need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

Step file is available if you want to make any changes.Be sure level the bed afterwards.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports:NoResolution: 0.15 mmInfill:30 %Filament: Prusament PC Blend Orange  Notes: I...

About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it...

About Gripen is a high flow fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it installed in...

You can use it internally like I have done here or anywhere you like.Next, load the filament in your extruder and you're done.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports: NoResolution: 0.20 mmInfill: 25% Filament:...

- belt driven extruder with a bowden system - xyz cartesian system - E3D all metal hotend - 40mm radial fan for heatsink - 2x30mm radial fan for partcooling - t8 lead screw for the Z-axis (up and down) - nema 17 steppermotors - 8mm brass rods (for...

Also added a link to a SherpaMicro Extruder and Carriage.Update 2022/10/24: Added instructions for adjusting the X,Y steps to accommodate the change from 17 to 20 tooth pulleys.Linear Rail UpgradeReplacing the 10mm rods on the X-Max (X-Plus) with...

Updated June 2022This carriage fits the Qidi X-Max (X-Plus) where the bearings are 29mm L, 19mm O.D., 10mm I.D.The stock Qidi X-Max carriage it is a pain in the you know what to switch between the low temp to the high temp extruders.This design moves...

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool...

There are four parts: Upper Guide, Lower Guide, Lower Guide Standoff, and PTFE Tube connector for BMG type extruders.The setup uses about 1.5 meters of PTFE Teflon tubing 4mm ID X 6mm OD 1.5:...