x max 3 3d models

The new X-Max version offers an ideal location for attaching custom fan ducts without requiring any modifications. However, users with older models will need to contact QIDI support in order to receive the updated part. This project serves as a...

I prefer using the lower filament holder for filament in my Qidi X-Max, but after a short time, the filament started rubbing against the ribbon cable during use. I couldn't find any filament guides for this area online, so I created one to solve the...

I've Upgraded the Remixed 3DBender Adjustable Stand by 3DBender for My iPhone X Max with a Speigen Kickstand Case. I've Modified the Larger Part with a Much Larger Diameter Bolt. I've Also Added a Second Large Part with a Cut Out for a Pop Socket...

Time Lapse Camera Mount for Action Cameras: A Seamless Solution for Flawless Footage Mounts easily onto the front tray of X-max, synchronizing perfectly with the print bed's up and down movements to capture stunning time lapse footage. Optimal...

This 2 models were printed using Black PLA + from esun: https://www.amazon.com/gp/product/B01EKEMDA6/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1The Camera is:...

Lid elevator for X-Max II by Qidi3D. Qidi suggests printing PLA with the lid off, but I like to make sure my cats still can't get in, so I created these elevators to allow for ventilation. Pre-rotated to print upside down, height set at 20mm in the...

I created this table for my Qidi X-max to replace the original spool holder. I had problems with back feeding and tangling with the original spool holder. I used the TUSH - A remix of many! from spongybob1958 for the actual spool holder. I...

This is a Z-max endstop that leverages the original z-min endstop switch, seamlessly integrating into the extrusion with a precise press fit.\r\n\r\nUsing this setup with a Duet Maestro facilitates power loss recovery for added...

About The QIDI X-Max Modular Tool Holder is just like it sounds a modular tool holder system for the QIDI X-Max that attaches with a spring design to one of the handles in the printer. The base has two slots for attachments, I made a few...

If you want to switch your Qidi X-Max from the (slightly frustrating) original firmware to Klipper, then the original touchscreen cannot be used anymore. But it is possible to use other touchscreens on your the RaspberryPI (which runs...

This is sort of a double remix. ...I initially printed this (https://www.thingiverse.com/thing:3434928), but I didn't fit the max. I really liked the roller on it, so I adapted it to work. ...You can print the roller as is and use this mount.

This is sort of a double remix. ...I initially printed [this](https://www.thingiverse.com/thing:3434928), but I didn't fit the max. I really liked the roller on it, so I adapted it to work. ...You can print the roller as is and use this mount.

This is a Z-max endstop that uses the original z-min endstop switch, the part press fits into the extrusion. I am using this with a Duet Maestro for power loss recovery. I have also remixed clips to keep the endstop cable tucked into the extrusion...

Max Bracic, I'm committed to crafting a tribute model tailored specifically to you, using 3D file formats STL and OBJ for rendering precise details. ...Additionally, the output will support the open industry-standard, human-readable formats for the...

This template is designed to take full advantage of the Ultimaker 3's maximum build area. ...For more information, refer to the upcoming article and watch the video at https://youtu.be/5Mm4-TbUefA, which provides a detailed explanation of these testing...

This is a Z-max endstop that uses the original z-min endstop switch, the part press fits into the extrusion. I am using this with a Duet Maestro for power loss recovery. I have also remixed clips to keep the endstop cable tucked into the extrusion...

... This will make the filament spool spin perfectly! Filament rolls with an inner width from 40mm to an outer width of 70mm can be used. The left and right frames are the old ones. Print Settings Printer: X-Max Rafts: No Supports: Yes Infill: 20%

Redesigned Z limit switch mounting for the Qidi X-Max (may also work on X-Plus, but have not confirmed dimensions). This design brings the switches closer toward the front in order to clear the lip of the steel platform when mounted upside down. ...

Super BIG Shout out and Thanks goes to CWILLS75 for the Qidi X-Plus & X-Max Carriage BMG Extruder & Dragon or V6 Hot-End Mod!!! With that, I was able to set up this simple remix setup to run the Titan Aero extruder/hotend which I originally wanted...

For security, the hinge locks at 90 degrees so it cannot be overextended.Notice: It doesn't fit all X-Max printers, some printers don't have the mounting holes but you could drill these yourself (see mounting instructions below).Which version to...

This is to allow one to install the Octopus Pro motherboard into the Qidi-Tech X-Max chassis. Has an offset to allow the wifi antenna to protrude outside of the metal under carriage, potentially giving you better wifi performance. Also drops...

This is a remix to the Max filament guide by Opendorrpolicy. This has been changed to a single sided bearing arm which aids in filament loading, allowing you to focus on getting it through the sensor first then placing it around the bearing after. I...

Someone asked me on Reddit if I could modify my two battery box into a 3 battery box, and I decided that the clip system wouldn't work well for a rectangular shape designed to hold three batteries. So I came up with a sliding lid box, which is...

Reducer compatible with up to 3 joules of energy is highly adaptable on various firearms platforms including the M4 rifle which shares identical specifications to the M16 but features a shorter barrel. A simple adapter can be easily attached allowing...

Took me a while to patch the original together, hopefully someone else can edit the holes or something. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 100 Infill: 35 Filament: Hatchbox PLA Orange ...

The standard Qidi X-Max spool holder is unfortunately uncomfortable to use and creates a lot of friction when unwinding, for example because the axle diameter is much smaller than the inner diameter of the spool. I have tried to improve all the...

QIDI X-Max Dragon Hot End Remix This is a remix from https://www.thingiverse.com/thing:4630835 I have made the following changes: - The mounting location for a 40x40 mm l/h hot end fan is moved for 7 mm to the inside. - That fan has now a third...

Others required forcing the cable into the opening and wasn't a fan of risking cable damage so I created a more open version with protective fillets.Hope this helps,Cheers.Print SettingsPrinter:QIDI...

They are optional, but I wanted to go the extra step to minimize any air leakage around the fan.Change Log:2021-07-23 Added a second stl with a wire tab off the fan shroud to hold the heater wires in place.Print SettingsPrinter:QIDI...

... at http://www.thingiverse.com/thing:41108, created using the Customizer tool found at http://www.thingiverse.com/apps/customizer/run?thing_id=41108. ...The specifications for this custom version include a width of 3, thickness of 3, and length of 3.