x carve y axis stiffening 3d models

This is meant to stiffen the Y axis rails of the X-Carve by providing a tie between the rail and the table the machine is attached to. Two sets of pieces are used, four brackets which tie into the side waste board mounting holes and brackets (I used...

This is meant to make the Y axis rails of the X-Carve stiffer by providing a tie between the rail and the table the machine is attached to. There are two sets of pieces, 4 brackets which tie into the side waste board mounting holes and brackets (I...

Upgrading the y-axis extrusions on my machine to 40mm Wide Makerslide provided greater strength and rigidity, but the curves didn't align properly with my machine's specifications. Therefore, using Phraust's design as a foundation, I started from...

Quick remix to use magnets I already had. ...6.1mm x 1.5mm specifically. Also removed the overhangs for ease of printing. I've included a STEP file if people want to alter it for their own magnets. ... Category: Parts

<p>Quick remix to use magnets I already had. ...6.1mm x 1.5mm specifically. Also removed the overhangs for ease of printing. ...I've included a STEP file if people want to alter it for their own magnets.</p> Category: Parts

This is a modification on https://www.thingiverse.com/thing:1844698, which itself was a variation of https://www.inventables.com/projects/mwp-y-axis-braces and https://www.inventables.com/projects/mwp-y-axis-belt-dust-guards. The files associated...

Adjusted height accommodates Y-Axis Stiffeners for optimal performance. My changes: Magnet towers are now integrated into the side wall, allowing for continuous printing without repositioning the hot end. The towers are 1.2 mm thick to support...

Users can now purchase wide Y Axis covers that accept 1/4" rare earth magnets at Michaels stores. An updated Z Axis cover has been created by Phraust, allowing for a Z limit switch to be installed while maintaining clearance around the Dewalt 611...

This OpenSCAD program designs left and right protective covers for the X-Carve Y motor pulley assembly. The X-Carve CNC machine's tendency to produce dust and chips necessitates these covers, which safeguard the assembly from debris accumulation.

Z axis knob for X-Carve. ...It turns really hard without knob when machine is off.</p> Category: Other

The X-Carve's Z-axis knob requires a firm grip when the machine is not operational due to its rigidity.

This is for stiffening the Y-Axis of your X-Carve. Per stiffener, you need: 2x m5 x 8 mm button hex screw (https://s.click.aliexpress.com/e/_d8YF8cV) 2x m5 t-nut (https://s.click.aliexpress.com/e/_dSRSU1X) OR drop-in t-nut...

I saw some of the other x-carve z axis spinners and I wanted to make one that spins it more freely so I made a crank type spinner. Needs a short M4 bolt and one or two washers. Bolt should self tap the hole in the knob. ... EDIT: Now with Knurled knob ...

This is a custom cover for the Z-Axis belt on the Inventables X-Carve CNC Router, keeping dust and chips at bay. I opted to create my own version from scratch rather than remixing http://www.thingiverse.com/thing:1326000. My design features tabs that...

I built a crank-type spinner for my x-carve z-axis, giving it more freedom to spin. To make it work, I needed a short M4 bolt and one or two washers. The bolt should be able to self-tap into the knob's hole. Later on, I upgraded the knob to a...

To reinforce your X-Carve's Y-Axis, you'll need the following materials for each stiffener: * 2x M5 x 8 mm button head hex screws (available at this link: https://s.click.aliexpress.com/e/_d8YF8cV) * 2x M5 T-nuts (you can find them here:...

This is for stiffening the Y-Axis of your X-Carve. Per stiffener, you need: 2x m5 x 8 mm button hex screw (https://s.click.aliexpress.com/e/\_d8YF8cV) 2x m5 t-nut (https://s.click.aliexpress.com/e/\_dSRSU1X) OR drop-in t-nut...

I saw some of the other x-carve z axis spinners and I wanted to make one that spins it more freely so I made a crank type spinner. Needs a short M4 bolt and one or two washers. ...Bolt should self tap the hole in the knob.</p> <p>EDIT: Now with Knurled...

I saw some of the other x-carve z axis spinners and I wanted to make one that spins it more freely so I made a crank type spinner. Needs a short M4 bolt and one or two washers. ...Bolt should self tap the hole in the knob.</p> <p>EDIT: Now with Knurled...

Quick makeover using readily available magnets, precisely 6.1mm by 1.5mm in size. Overhangs have been eliminated for smoother printing. ...A STEP file has been added for anyone looking to customize the design for their specific magnet requirements.

... Step 1: Insert Magnets Push the magnets into the holes on the piece. I used a C-clamp to press them in flush with the rim. Step 2: Install Cover Just put the cover on. You won't have to take anything apart from a stock X-carve (1000mm).

... hardware (magnets, nuts, bolts, etc.). ... The design is inspired by classic car valve covers and oil filler cap. You will need to print two copies of the M5 nut. This should work o x-carve versions September 2016-November 2021 with standard z-axis.

You'll be needing this part for the X-Carve system designed by Inventables. The purpose of this small accessory is to secure a rotating knob onto the hexagonal nut, allowing you effortless control over the Z-axis motion when your machine is in...

A simple cover to cap the Z-axis. ...The design features an internal grip that secures itself around the existing bolts without needing additional fasteners.

Here is a remix of PopsActual's Z-axis cover, tailored to fit the upgraded 9mm belt Z-axis system. ... The changes I implemented include reducing the length of the original cylinder design to ensure seamless compatibility with the new hardware.

This slightly oversized rendition of the ILikeToMakeStuff knob fills the bill by matching the M6 nut on top of the ACME Z-Axis Rod perfectly while also providing a comfortable amount of clearance for the Dewalt 611. Take a moment to browse through...

The X, Y, and Z axes provide a crucial framework to grasp and navigate directions swiftly and efficiently.

Calibration with a 20mm cube simply won't cut it, this piece measures in at a full 100x100 mm - more than enough for calibration purposes.\r\n\r\nPrint out the design on your printer and double-check those dimensions before making any adjustments to...

A stiffer **stepper motor mounting bracket** and **pulley bracket** for the Y axis of the Wanhao Duplicator i3 Plus (I have a Mark 2) The **stepper motor bracket** utilises a longer centre rear panel screw (M5 x at least 20mm) with a washer and M5...

Model to test X or Y axis deviation between 2 nozzles for printer with IDEX - independent dual extruder.