x cam 3d models

Possibly fixed somehow to the x-gantry so the cam would follow the printhead up. I'm convinced someone did such a thing before as the idea isn't far fetched, however, I couldn't find anything so I tried my own solution. This thing is a clip-on,...

I build a pillar for the backside to hold a cam before (https://www.thingiverse.com/thing:3978597), now I was searching for a thing to mount a second cam at the right. Possibly fixed somehow to the x-gantry so the cam would follow the printhead up. I...

PRINT INFO: Filament type: PLA 4 Top/Bottom layers 3 Perimeters (only 2 perimeters for Cam mount) 0.2 layer Infill: 15% - (I use "Gyroid" in Cura) Bed adhesion: if needed Support: YES - (I use "Tree Support" in Cura) Hints: - Print the cover on the...

Two critical holes on the cam enable it to function in both directions, simply rotate the lever towards the bolt you are using by turning it in the direction of the adjacent arrow. The hole marked with a counter-clockwise arrow is slightly recessed...

This is a custom 3D printed cover designed for the "Pi Cam Prusa i3 MK3 Camera Mount Swivel Package". ...It requires components sourced from the Thingiverse website at https://www.thingiverse.com/thing:2873677.

First, insert the rectangular section between the cam boards. Hold the cam in place while stretching the front loop over the lens. ... Options include: - A 16x16 0-degree configuration available at https://www.thingiverse.com/thing:2710413 - A tiny...

TPU 20 degree camera mount for 16mm boards turned 45 degrees. Put the rectangular part between the cam boards first, hold the cam in place, and then stretch the front loop over the lens. 16x16 0-degree:(https://www.thingiverse.com/thing:2710413 Tiny...

It's designed to use these bolts to mount the Insta360 One X - https://www.mcmaster.com/93180A208/

The Proton X 40-degree cam mount from the FPV Flight Club is a game-changer for aerial videographers and photographers. ...Paired with the Runcam Racer camera, this dynamic duo captures stunning footage from any angle, making it perfect for capturing...

... it longer as well. ... Also the camera case did not fit my v2.1 Pi-Cam, so I remix the case from [Ender 3 Pi cam mount by BartPLA](https://www.thingiverse.com/thing:3868687) and used the ball-connector from this design to allow it to connect. ...

This action cam support is specifically designed for the QIDI X-MAX printer and tailored for use with the "cooau 4K" camera or similar models.\r\n\r\nPlease take careful note of your Action cam's size.\r\n\r\nIf you opt to use a different action...

This was a simple change allowing the part to fit a Mizar S

This is a Remix i added a hood over the lens for light glare.

... ...I've added some space to accommodate a bracket from http://www.thingiverse.com/thing:2886101 - that's where the magic happens for the damper installation, and you'll still need the Ender_3_X-axis_mount_plate for it all to come together seamlessly.

I wanted the stowable pi cam mount on my printer, but the Voxelab Aquila is a clone of an Ender 3 V2, not an exact copy -- the Aquila x-axis mount gives the original Stowaway Pi Cam for Ender 3 ( https://www.thingiverse.com/thing:3426025 ) nowhere to...

... as one piece. ...After screwing with the hex screw M5x16 and the T-nut (or M4x16), turn the cam with a wrench. The pieces will separate and the cam mechanism will work. ...Before tightening, loosen the screws of the belt fastening in the profile.

Customized version of https://www.thingiverse.com/thing:2749041 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2749041

I source my standard 56mm model rocketry body tube fins from Apogee Rockets in an 18-inch length. ...Be sure to check out my other content featured here for additional information.

I modified the cover of https://www.thingiverse.com/thing:3147295 to fit the new Raspberry Pi Camera 3. ...

This is a remix from: Ender 3 Pro IR CUT Camera with Z-Axis Mount by mardun on Thingiverse: https://www.thingiverse.com/thing:4407112 and it uses the clamp piece from this model Ender 3 V2 X-Axis Tensioner Mount:...

It allows the ESP32-CAM to be mounted on the side of the X-axis motor cover of an Ender-3 or similar printer. The mount fits snugly and holds in place through friction, but you can use glue for added security. The camera is positioned to point at the...

Cam Sync HD, pour Octoprint Adaptation du modèle de fuchsr (https://www.printables.com/fr/model/64402-raspberry-pi-camera-mount-for-mk3s) pour la webcam Creative Live! Cam Sync HD 720p. Vous devez réutiliser les 2 vis et les 2 joints du support...

It is designed to fit a custom X- Belt tensioner for an Ender 3/Pro, especially the Tevo Tornado X Belt Tensioner for Ender 3 Pro (https://www.thingiverse.com/thing:3319649) but will probably fit anything with a diameter of 32 mm. All screws and nuts...

It is designed to fit a custom X- Belt tensioner for an Ender 3/Pro, especially the Tevo Tornado X Belt Tensioner for Ender 3 Pro (https://www.thingiverse.com/thing:3319649) but will probably fit anything with a diameter of 32 mm. All screws and nuts...

I'm using sturdy ball joints derived from the source (https://www.thingiverse.com/thing:3412413) and a socket that clips into the x-profiles of my Anycubic Kossel, everything printed at 0.2 mm without supports. The ball joints will likely benefit...

I enjoyed the original camera mount, but I wanted the camera closer to the X gantry so I shortened the arm. Update: (V3) Added the cable clip for the Sprite Pro. ... Update: (V4) Added a cutout for the No Y offset CR touch mount found at...

I am a Text Rewriting Bot, and I will rewrite the text according to your instructions. ...Please provide the original text.

I'm ready to assist you with spinning the given text. ...Please provide the original text.

I created this because I wanted a bed level front view mount for my Wyze Cam v2 on my X-Max. I designed it to be flexible enough to stay out of the way of things, yet sturdy enough to get a good view for videos and time lapse. You'll need to print...