x axis 3d models

Complete transmission assembly from X axis of Taig CNC mill. I measured my own mill and designed all the parts natively in Fusion 360. (Except stepper which I found online and modified to match my stepper shaft). The mill is the V-thread leadscrew...

Due to the the solid top of the on the extrusions for the Neptune 2 and differing geometry for the extruder plate, there wasn't a good way to attach the cable chain for the x axis and extruder wires. The back mount simply replaces end cap of the...

Upon closer inspection, I observed the thin metal frame on the X-axis arm vibrating in resonance. Seeking to resolve this issue, I applied a piece of tape tightly to the arm and took note of its effect (see attached picture). With some success, I...

Designed this Minimalist x axis tensioner for my ender 3, i made it as small as possible to not have a distracting look when installed on the printer. ...It tensions using an m3 bolt/nut and an allen key.</p> <p>A couple notes:</p> <ul> <li>Since this...

This design incorporates a floating X axis idler to help reduce Z wobble artifacts. Currently it is using an old fan duct design and it is also compatible with my Z endstop adjuster. I will later update this for use with 450mm rails (what I should...

You can find that video here if you're interested https://www.youtube.com/watch?v=ttPl8WxwHwE Problem is while prints have been perfect since then there has been an issue of the print head assembly not staying firmly against the x axis end stop...

It only requires two small pieces that easily fit into the existing bearing block, with tension directly applied to the X-axis guide rods. Only 9 grams of filament are used, printed in 30 minutes, yet it performs the exact same task as tensioners...

Designed for the Logitech C925e camera, but accepts all standard cameramount 1/4-20 hardware on the camera side Bolts to the X Axis with an M3x16 bolt Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 0.20...

Remix of the Extruder Gyroscope Print in place with press fit magnets&nbsp;This gyroscope snap onto the Prusa Mini+ x-axis shaft without any magnetsIt is made for the Purse Mini+ but should be compatible with the MK3If not, let me know and i will try...

This approach is less intrusive than the one involving trimming of the upper bearing housings with a hacksaw in order to increase clearance from the x-axis belt, but there are some things to consider (see further down). You will need 2 of each: ...

This belt mount allows you to attach the x-axis belt to the 3D printer's carriage, without using the stock Anycubic hotend housing. If you are using your Anycubic i3 Mega for 3D printing, this part is not for you. However, I want to convert my...

So when my X axis tensioner broke, it was of course in the middle of an important print. I got massive layer shift and a big surprise first thing in the morning. I pulled the tensioner out, and it was really bad. I made this so I could have a...

This is a fairly accurate representation of the x-axis limit switch on my Ender 3 Pro. I took the STEP file from [Creality's...

This is a replacement X-axis assembly I created for my Tevo Tarantula (but it will work with any 2040 extruded aluminum setup). I drew inspiration from http://www.thingiverse.com/thing:1580899 and modified the design to make it easier to print and...

This clips on the cover for the Ender 3 series (including V2) X axis end stop. Apparently also works for the Mingda d2. Whoda thunk it? It comes in two pieces and is joined with an M3x16 screw and nut. Created to get my direct drive cable...

I was using my own remix of the Anet A8 X-axis tensioner rod and it failed miserably. As seen in the photos, the part was severely compromised where the material was incredibly thin around the hex nut recess. This design attempts to fix this issue in...

This is a modified version of jtenkely's Keystone Stepper Motor Mount, with the keystone rotated and moved, to fit on the back side of the Replicator 2's X Axis Stepper Motor. The screw plate has been cut to fit against the standard MakerBot chassis...

My take on an X Axis Belt Tensioner for the Anet A8. 2 versions available: 8.75mm Inner Gap and 10.00mm Inner Gap. ### Update includes correct placement of the nut. I apologize for this mistake. If you printed the old design, secure the nuts in...

Designed this Minimalist x axis tensioner for my ender 3, i made it as small as possible to not have a distracting look when installed on the printer. It tensions using an m3 bolt/nut and an allen key. A couple notes: * Since this is smaller and...

Replacement X-Axis belt tensioner designed for Voxelab Aquila printer. Designed to use mainly stock parts only. Fits into the end of the 2020 extrusion and secures with M5 pan head screws, two of which come with the stock tensioner. Pulley is the...

It replaces the X-Axis limit switch cover (The thing with the QR code sticker on it) with one that has M3 screw holes for mounting other attachments. You can then attach to that: * Main Mount and Ethernet Retainer: This has a cable holder (and...

Replacement X-Axis belt tensioner designed for Voxelab Aquila printer. Designed to use stock parts only. Fits into the end of the 2020 extrusion and secures with an M5x14 pan head screw, two of which come with the stock tensioner. Pulley is the same...

This belt mount allows you to attach the x-axis belt directly to your 3D printer's carriage without using the standard Anycubic hotend housing. If you are using an Anycubic i3 Mega for printing, this part is not necessary. However, if you want to...

This is a nearly exact replica of the stock Anet A8 X Axis mounts in newer molded versions.\r\n\r\nThe reason I created these was to change the color scheme of the printer from black and white to black and orange, as it looks awesome and the stock...

Other parts I've designed for my Prusa i3 steel upgrade include: - http://www.thingiverse.com/thing:1959901 (GT2 belt clamp for the Prusa Y-axis) - http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case) -...

It was crying out for an independent dual x-axis conversion, so I looked around here and printed various parts and made it, and it turned out to be awesome. A picture is printing a part in PETG with PLA support, which breaks away perfectly. Most...

I was never really satisfied with the x-axis on this printer and was getting a lot of ringing because of its lack of stiffness. The idea to use the open-builds v-wheel system for my x-axis came from Sonny Lowe, which really caught my attention. I...

This is a remake of CR-10 X-Axis Tensioner" by donnyb99. I barely changed anything, I truly loved the design and the things I altered were mainly just to make this work on the Adimlab Gantry-S printer. The main thing I remixed was adding mount holes...

This is a remix of CR-10 X-Axis Tensioner" by donnyb99 on Thingiverse. I didn't change that much, I really liked the design and the things I changed were mainly just to make this work on the Adimlab Gantry-S printer. The main thing I remixed was to...

UPDATED: Added a second tensioner for a Gates GT2 idle This is a remix of the x axis tensioner by ivango2, but I encountered an issue with the original fitting and pivoting around the bolt head for the z axis wheels so I expanded the pivot 2mm. To...