x axis prusa 3d models

http://www.thingiverse.com/thing:691547 Print Settings Printer: The Aurora Z605/MK8 printer is used. Rafts: No rafts are printed. Supports: Yes supports are included to prevent warping. Resolution: A resolution of 0.2-0.4mm is selected. Infill:...

Modified directly from STL file packaged with my Aurora Z605.

Easy Setup for Hot End and Bowden Extruder: Use Belt Fix With 4 Lm8UU Pulleys And Secure With One M3 Screw.

for 8mm rods added top clip not available in customizer to hold i place while manually adjusting height i would suggest printing two in one run to make calibration the quickest just put one on each side and lower till they match remixed from...

Customized version of http://www.thingiverse.com/thing:280974 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=280974 Instructions Using the following options: z_distance = 100 beam_width = 10 rod_diameter = 8.2...

<p>Probably the most over-engineered strain relief in the world? Intended to be printed without supports. ...Put a little superglue on the locking dovetails.</p>

for 35mm rods added top clip not available in customizer to hold in place while manually adjusting height i would suggest printing two in one run to make calibration the quickest just put one on each side and lower till they match remixed from...

This is the X axis tensioner modified to fit a 5 mm center pulley, the metallic ones. The original part has been slightly altered to accommodate a 5 x 20 mm bolt and the 5 mm nut, ensuring they don't come into contact with the metal structure. If...

I designed an Open Builds Acme Lead Screw and Nut Block conversion for Prusa X axis using Designspark Mechanical. The conversion utilizes the M8 Lead Screw and Nut Block from http://openbuildspartstore.com/nut-block-for-8mm-metric-acme-lead-screw/,...

The upper path is for the Bear x-axis, while the lower path is for the Prusa x-axis. Simply push the belt ends into the corresponding slot for your axis. Since this carriage is based on the BNB Easy Motor Service carriage for the Bear extruder, you...

Additionally, I have repositioned the X axis motor screw mounts a few mm to the left, as they were previously too close to the emergency stop button on homing the Z axis where the Ramps board is mounted on the BQ edition. Furthermore, I have...

The operator raises the X-axis to free up the print head for operation.

My modification of the Taurus X-Axis motor part has been optimized for seamless operation with both stock and BMG extruders. ...Still, you may need to carefully trim or sand approximately 0.5 millimeters from the lower left trapezial nut to ensure a...

http://www.thingiverse.com/apps/customizer/run?thing_id=280974 These Models are Larger than the Original and Designed to Work Well on My FolgerTech 2020 Prusa i3 Instructions for Use Selecting the Following Options: Claw Height is Set at 15 Units...

It's X axis motor cover for Mini Bear With Prusa text

Robust and reliable Prusa I3 Steel X and Z axis mechanical endstop holder. Securely fasten with a 20 mm M3 screw featuring an Allen head and nylon insert lock nut. ...Printer Settings Manufacturer: Prusa Model: Prusa Steel Raft Support: No Supports: Yes...

Prusa i3 MK3 Cable Chain Add-on (ALL AXIS) https://www.thingiverse.com/thing:2862375 X Stepper sleeve wire clamp https://www.prusaprinters.org/prints/3436-x-stepper-sleeve-wire-clamp The default heatbed cover from Prusa Print Instructions Additional...

Counterweight to compensate for the difference in mass on both sides of the X-axis in the Prusa/Anet BLV MGN12 mod: https://www.thingiverse.com/thing:2567757 The weight is Madcat BB Swivel Lead 300g:...

... precise idler gear model after discovering that other models allowed too much play in the mechanism. ...This new design is specifically tailored to fit the X-axis end idler from the Prusa MK2 model, and I'm thoroughly satisfied with its performance.

The original holder failed due to a rotated x-axis endstop switch, leading to uncontrolled head movement. This revised model rests securely on both x-axis rods and was introduced at year-end 2012. Inspired by user interest in another modification,...

I've Constructed a Frame from Rectangular Steel to Enhance the Z-Axis Bracket on My Prusa I3 MK2 X. To Improve Printing Precision, I'm Using Ball Bearings 605ZZ to Minimize Swings of the Z-Axis. You'll Never Notice Any Z-Wob Again! Note: The Pink...

A custom holder for Logitech webcams like the C920/C930E is designed specifically for the Prusa i3 MK3/MK3S X-axis nema 17-motor. This holder retains the original hinge to maintain tilt functionality. The webcam itself is shown in the last image. If...

A holder for a Logitech C920/C930E webcam without the heavy base for a Prusa i3 MK3/MK3S X-axis nema 17-motor. Uses the original hinge to keep tilt functionality. Last picture is from the webcam.</p> <p>It requires disassembly of the camera, but it...

Other models that I found gave too much wiggle room for the idler gear, so I decided to model my own and I'm really happy with it. It's made for the X axis end idler from the prusa mk2 model. Print Settings Rafts: No Supports: Yes Infill: 40%...

v2 of my diy x-carriage design, original at https://www.printables.com/model/276122-prusa-i3-e3d-v6-x-axis-carriageNo support needed to print the carriage or part cooling fan guides, some support needed to print the clamp/fanmount and BLtouch...

This is a major upgrade to the X-Axis of the CTC Prusa I3 3D Printer and all similar I3 clones like the Anet A8, designed to utilize an upgraded 2020 V-slot aluminum profile as the guide instead of the original steel rods. The aluminum guide paired...

I Made This After My Prusa I3 Hbi3 Kept Overshooting the Build Plate on Both X and Y Axes, Requiring Me to Sand Down the Y Adjustment Outer Shell for a Perfect Fit.\nPrint Settings\nPrinter:\n Prusa I3 Infitary (HBI3)\n \n Rafts: No\n \n Supports:...

At the terminal point of the x-axis, sturdy steel rods will securely fasten into place. Exercise caution, as I embark on this project with some trepidation: it's a new endeavor for me. ...Guten Tag from Deutschland.

I decided to make this after discovering that my Infitary i3 would overshoot the build plate on the x and y Axis. ...Sanding might be required to have Y adjustment outer shell fit.

I added a small flange at the top that aligns with the X-axis endstop mounted to my X-carriage:http://www.thingiverse.com/thing:672253. The setup is working really well so far. ...Instructions: Print in PLA, 40% infill, no special requirements except...