wyze cam v3 window mount 3d models

I needed a Wyze Cam mount for my Ender 5, but every design available online was specifically made for an Ender 3. So, I made some modifications to the existing design. I redesigned the slot tab to fit perfectly with my printer and added a tension...

... A precisely crafted opening at the top accommodates the official Wyze mounting ring, allowing it to snap into place and secure the camera with magnetic force. ... Comprehensive accessories include cable clips designed to keep USB cords organized.

This mount snaps onto the metal frame of the Anycubic i3 Mega and holds the Wyze camera off to the right or left side of the bed. The Wyze camera can then be articulated to point in the desired direction. ... UPDATE 2/11/19: Added a clip for the USB...

... by the extruder assembly. ... This piece should seamlessly integrate onto existing components, as I simply attached the Wyze camera mount to the top, where the original camera mount was situated. ...No adjustments were made to any connecting parts.

... the extruder assembly. ... This piece fits onto the existing portions perfectly because I simply attached the Wyze camera mount to the top, right where the original camera mount was located. ...I didn't make any adjustments to where the pieces connect.

... store the floor vacuum attachment. So I designed this wall mount to hold the floor vacuum attachment while the crevice tool is installed on the vacuum full time. This wall mount should work for just about any of the other Wyze vacuum attachments.

FIXED Version. ...This is a Wyze camera mount I created for the Anycubic Mega Pro, I'm sure it fits other Mega's but not 100% Sure. ...Straight forward installation.

I Doubt These are Universal and May Lack Rigidness, But I'll Try It Out Soon as the Original Ones Installed in Our Windows Have Become Brittle Over Time and Crack Easily. I Printed the Replacement Cam in Normal PLA but Might Attempt Something...

This design is based from: https://www.thingiverse.com/thing:3838066 Secure Wyze Cam Pan, I just needed one that was angled a little less. You will need a 1/4" nut and bolt to attach to the bottom of the camera. Chances are you will not find a...

There are many wall mounts for the Wyze Cam Pan, I just needed one that was angled so I can mount it high and see the whole room. It has a relatively small hanging hole, I hung mine on a finishing nail. You will need a 1/4" nut and bolt to attach to...

This WYZE camera mount is designed to mount to the bottom left of the Ender 3 next to the SD card slot using the screws which come in that position (no additional screws needed). ... The camera is mounted at bed level to give you a clear view of the...

I created a Wyze camera mount that snaps perfectly into the frame rails of my Ender 3 Pro. To get the best possible results, I recommend printing it with the camera mount facing downwards or on its side. ...Now I can enjoy seamless monitoring of my...

Wyze C2 Camera Suction Cup Mount. This mount can also accommodate any screw or mount system since it features keyhole-type mounting holes. I printed it with a high infill rate (75%) to make the part extremely sturdy; a lesser infill of at least 30%...

A versatile mounting solution for the Wyze Sense motion detector, designed with customization in mind. ...Two strategically placed holes allow for effortless installation using screws or a reliable 3M double-sided adhesive, ensuring a secure and precise...

I acquired a Wyze camera to keep tabs on my prints, but I soon realized that I didn't want to attach it directly to my printer, so I decided to create a custom mount that would allow me to position it just ahead of the print bed instead.

The mount securely fastens onto the Anycubic i3 Mega's metal frame, positioning the Wyze camera at an offset on either side of the bed. The camera can then be angled precisely to capture any desired view. ...A small clip has been added to manage the USB...

A simple 45 degree ceiling/corner mount for the Wyze Sense Motion sensor. This is meant to be fixed with double sided tape to the corner of a room against the ceiling. ...The sensor can be attached with the included double sided tape.

Camera mount to attach a Wyze camera to your Ender 3 S1. It's still a WIP as it'll require a dab of hot glue to actually hold on to the printer.&nbsp;</p><p>Prints easily on my Ender 3 S1, just have to flip the model 180* so it'll sit flat. ...No...

I wanted a mount for my Wyze Doorbell Pro's that I could easily adjust horizontally and vertically after mounting and could not find a viable solution, so I created one.I originally intended only to use double-sided outdoor foam tape to hold the base...

This is a remix from https://www.thingiverse.com/thing:4210431 I changed the mount to accommodate a Wyze v2 camera. This needs to be printed upside down with supports. ... In the pictures there are holes to secure it to the frame but they are...

wyze cam2 mount No hardware required... like additional metal swivel joints or bolts that cost money. Aside from like 2 paperclips or a thick wire to jam into the holes on the adjuster arms but that's not really something that is a expensive item. .

A stylish angled corner mount for the Wyze Motion Sensor. Since the sensor is in my bathroom and it looks like a camera, I made a cover that I can install if I'm having guests over. I've simply mounted mine to the wall with a little square from a...

I removed the original mount to make way for this new version, which is easier to install in the Extrusion and doesn't require nuts to hold it in place - just tighten the 2 M3 screws. Use 10-12 mm long M3 screws when installing. The CAD model is...

This is a sleek mounting system for your Wyze camera, specifically designed for 2020 extrusion. As shown in the photo, this mount is perfect for use on my Tronxy X5SA-400, allowing you to achieve a smooth and compact setup. To install it, simply...

A sleek corner mount for the Wyze Motion Sensor that makes a stylish addition to any room. Since I placed mine in my bathroom and it resembles a camera, I crafted a cover that can be easily installed when hosting guests. I've simply attached mine...

*** ### FITS THE WYZE CORDLESS VACUUM S (yes, the one from Wal-Mart) & WYZE CORDLESS VACUUM ### *** Recently bought the Wyze Cordless Vacuum S only to realize that it didn't come with the Wall Mount that the previous model had come with. Luckily, I...

Wyze Vacuum S Wall MountThis is a remix of ciruittree's wall mount. Changes:thickened cord retainer attachmentstrengthened hook removed some non support walls to save filamentadded an additional section that "captures" the bottom vacuum hinge. this...

A parametric corner mount for Wyze Sense motion detector. It has two holes for mounting using screws (or 3M double sided tape). ...Customize the whole sizes to fit your screws.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>3D...

I'm sure it can work with other mounts too, that takes a ¼" screw to mount sideways.I did not add an indent for the round, meta plate (for the magnets in the Wyze stand). I made a design for it, but I really don't think it's necessary because the...

This is a remix from https://www.thingiverse.com/thing:4210431 I changed the mount to accommodate a Wyze v2 camera. This needs to be printed upside down with supports. In the pictures there are holes to secure it to the frame but they are really not...