wyze cam v3 cover 3d models

 The existing channel for the cable pass through is a bit tighter with the V3 due to there now being the little section of cable integrated into the camera, but I didn't mess with that...

UPDATE 2021-04-02 As requested added a new file CAM_MOUNT_V3 that should fit the base of the new Wyze V3 Cameras, use all the same files but use CAM_MOUNT_V3 instead of CAM_MOUNT_V2 which is for the V2 Base. Also added an arm file with no clips for...

Two Part Pegboard Mount for Wyze CAM V3 This design is a remix of my Pegboard mount for a Wyze CAM V2 to accomodate the V3. https://www.thingiverse.com/thing:4335549 This posting contains three files File 1001 Pegboard Bracket with a Cable...

Two Part Pegboard Mount for Wyze CAM V3 This design is a remix of my Pegboard mount for a Wyze CAM V2 to accomodate the V3. https://www.thingiverse.com/thing:4335549 This posting contains three files File 1001 Pegboard Bracket with a Cable...

I needed a mount for my Wyze Cam v3 to attach to my Snapmaker 2.0 A350, and found these other 2 things. I took the cam mount from cdoucet57 and connected to the the base from da96jdm. ... cdoucet57: https://www.thingiverse.com/thing:4938173 ...

NOTE:  This is the old version – for the updated version, please see this model:https://www.printables.com/model/207964-upgraded-wyze-cam-v3-mount-for-lack-enclosure-or-oMinimalist mount for the Wyze Cam V3 (and V2) which allows removal of the...

I was looking at other Wyze Cam V3 mounts for the Prusa Mini+ and saw that they all needed supports. So, I designed my own that uses no supports.  Print the model as it imports into the slicer. ...Then simply hang the finished part on the left hand rail...

Different iterations I made to make this work for the Wyze Cam v3 which has a different base size than the v2. ...This mounts on the Landroid mower's ACS mount screws and like the original still allows ACS accessory to fit on top.

Simple mount designed to attach the WYZE Cam Pan V3 to a camper slide out or any surface that is 1/2 inch thick. Suggest you use ABS or PETG for outdoor applications. 6-7mm self tapping screws are suggested. ...I added a rubberized pad inside to avoid...

I combined LuckyResistor's Snap-in Pipe Clamp with a basic Wyzecam V3 mount so that I could mount my Wyze Cam V3 on a 3 inch diameter downspout without drilling into anything. &nbsp;</p><p>First time “designing” anything. &nbsp;Used Tinkercad and...

**There are separate files for v2 and v3 of the wyze cam.** I believe the v2 file will also work with v1 cams. This mount likely fits the smaller A150 and A250 Snapmaker models, but no promises. ...On the A150 model the linear module for the x-axis...

Nice stable mount for a Wyze Cam v3 to the now-discontinued version of the Elfa Top Track (e.g., here). ...Note that this model does not have the snap-fit features to make it click into place on the Top Track, it just stays in under gravity – this is...

Since the Wyze Cam v3 is water resistant, printing the enclosure is optional, as you can mount the camera to the base without the enclosure. With that said, I do recommend printing the enclosure for additional protection. ... Additional Parts: ...

See assembly video: https://youtu.be/Ax71cyuve7M This is a an outdoor mount for a Wyze cam v3. Since the v3 is waterproof, the enclosure is not designed to prevent water from getting in, but rather allow water to filter out through some holes on the...

While you're waiting to print this, I'd suggest preparing the double-sided tape:Cut a length of 2 inches (or 5.5 cm) of Gorilla Double-Sided Tape, then cut it in half lengthwise.Remixed from:Wyze V3 Camera Window Mount by the_holocronWyze V3 Window...

- Slightly reduce size - it should be around the same size as the Wyze's window mount. - Support for the back piece - I made another back piece that has design-in supports. Use whatever version you see fit. ... ###While you're waiting to print...

Also gives slightly more plastic under the screw heads H - 2 horizontal holes V - 2 vertical holes 4 - Four holes C - Central hole The 'catch' was inspired by a creator that made a base for the Cam v2. I cannot find that Thing for the life of me. If...

Customized version of https://www.thingiverse.com/thing:3020851 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3020851

Print the design upside down with 15% fill. Place a piece of double-sided tape directly on top of the camera lens. Then, slide the printed design over the camera, pressing firmly to secure the adhesive in place. The dual USB feature allows for daisy...

Uploaded at lightning speed to satisfy your needs, this Wyze Cam cover is a clever creation, born from numerous designs and tweaked with my personal touch.

A rapid redesign of the Ender 5 Belt Covers now incorporates a WYZE camera mount conveniently positioned on the right-hand side.

The camera can be tilted 20 degree in every direction.Size and overall geometri like the Google Wifi points.The baseplate and the camhousing are connected with 12 magnets, size Ø4/2 mm.The parts should be printet in a temperature- and UV-resistant...

<p>Screwless mounting on LK Fuga Softline USB Socket.&nbsp;</p>

Version 1 - I will likely keep upgrading this and releasing new versions as i tinker with it.IMPORTANT - Make sure you orient in the 3d model in your slicer so its laying on its back, this will prevent the need to use any supports!! Best to print...

This is a remix from https://www.thingiverse.com/thing:398515

The camera can be tilted 20 degree in every direction.Size and overall geometri like the Google Wifi points.The baseplate and the camhousing are connected with 12 magnets, size Ø4/2 mm.The parts should be printet in a temperature- and UV-resistant...

Wyze Cam housing with a 45-degree camera slot now sits comfortably on the workbench, its box boasting an innovative lower compartment for effortless cable management. A couple of strategically placed ventilation slots ensure optimal airflow,...