wyze cam v2 target 3d models

... filament if it doesn't fit. 2. The wyze webcam monitor stand. I did not need supports for this print. Instructions to turn your Wyze Cam into a webcam: https://wyzelabs.zendesk.com/hc/en-us/articles/360041605111-Webcam-Firmware-Instructions

I desired a bed mount for a Wyze cam to facilitate the creation of time-lapse videos. My aim was to avoid adjusting the bed levelers and to have the flexibility to relocate it as needed during printing. ...ABS was chosen for its rigidity and heat...

This is a suction cup window mount to your Wyze Cam v2, it will accommodate suction cups with collars of 11-9mm. I used suction cups I got from Lowes, I have included a picture of the box. I tried to use as little material as possible. ** UPDATE **...

A mount to hold the base of a Wyze v2 or v3 onto the side of a dog cage or similar. We used this to monitor baby chicks in a cardboard-line cage. Created with onshape. ...The original models are available here:...

I utilize this fantastic Wyze Cam enclosure, yet make some modifications. I'm unable to print the hood so I create my own one. It also secures in place by utilizing these two tabs. I modify the ballmount to employ square nuts instead of...

This simple camera mount allows you to use the standard movable Wyze Cam V2 mount and place it into a holder that can easily screw into nuts in 1515 extrusion. I merged two of the "Things" listed as source material, and used the remaining bits...

A mount to hold the base of a Wyze v2 or v3 onto the side of a dog cage or similar. We used this to monitor baby chicks in a cardboard-line cage.</p><p>Created with onshape (free and web-based). ...The original models are available here: <a...

... pre-orientated for optimal printing, so be sure to adjust them accordingly. In the end, I'm thrilled with how this remix turned out, meeting my expectations perfectly. Hopefully, others will also enjoy using this design for their Wyze Cam Mounts.

Wyze Camera V3 bracket for the Ender 3 v2. It mounts right onto the front where the existing 2 screws are so no hardware required. Simply install the provided circle magnet with the camera and screw it into the mount. No hardware needed and you can...

I got my hands on the new Wyze Cam v3, which has been fantastic, but they changed the shape of the base slightly from the previous version which meant that the [existing...

Used the base of "Ender 3 v2 Spool Holder" by Pugwash" then just added a little platform for the cam to rest on. ...I tightened up the tolerances a bit to make the mount more secure so it ends up being a tight fit.

Wyze Cam

... face of it. Print Settings Printer: Ender 3 V2 Rafts: No Supports: No Resolution: .2 Infill: 20% Filament: Hatchbox PLA Black Notes: I used a brim to print this on the stock ender3 v2 bed, your mileage may vary. ... Category: 3D Printer Accessories

WyzeCam mount for Ender 3 V2. Mounts to the front leveling screws on the printer. I designed it with clearance but it ended up a little tight on the base of my WyzeCam, may need to scale it up a hair if it's too tight. ...Doesn't need any supports,...

The Wyzecam v2's versatility is enhanced by its compatibility with a range of mounts and accessories. For users seeking to place their camera indoors, the window mount provides a convenient solution. This allows for a discreet installation that...

This is a remix of Surketry's mount. Its a great design but it was too close to the hot end shroud while moving across the X axis while at Y-0 and would clip it going by so I extended it about 25mm longer, The camera wouldn't slide in the base...

... wouldn't slide in the base without massive force because of the rubber feet that are on the camera so I also made notches to accommodate. I added spring seats where it mounts to the bed. I also added the text "Ender 3 V2" on the face of it.

... be warned that too much and the mount will become loose. To mount the camera, you'll need to unscrew the single nut/bolt at the base of the cam as the factory foot is not needed with this setup and will not allow the camera to be fully inserted.

I couldn't find a Wyze V2 mount for my Ender 3 V2 Neo that did all the things I wanted so I made one. Attaches to the front with the factory screws. The actual V2 mount plate was made by jitterzPrintz and can be found here...

Please share a photo when you print this piece :D Wyze Cam v2...

This is a custom-designed mount engineered by Jelkinsiv Remix specifically for the IKEA SKADIS line of products, tailored to seamlessly integrate with the Wyze Cam V2.

This is a custom mount designed specifically for the Wyze Cam V2, created by jelkinsiv as a modified version of the IKEA Skadis base.

Custom Umbrella Lock Prevents Tilting Mayhem This clever lock is specifically crafted to stop patio umbrellas from spinning wildly when tilted to block the scorching sun's rays. Designed for a sturdy 37mm umbrella pole, it's also suitable for sizes...

<p>Mount with some double stick tape.</p>

I use this camera for web chats and wanted a better way to block the eye than a post-it note that kept falling off. ... Simple cover and you can turn it 90 degrees to use the camera.

1 Two Part Pegboard Mount for a Wyze CAM V2 https://www.thingiverse.com/thing:4335549 2 Two Part Pegboard Mount for a Wyze Contact Sensor Switch Holder https://www.thingiverse.com/thing:4337294 3 Wyze Motion Sensor Pegboard Mount...

Easy print (~2hr), no supports.I designed this with the mindset that the Wyze Cam v2 has a nice ledge along the bottom that's perfect for ‘locking’ the camera in place if one installs it upside down.PLA0.2mm layer height0.4mm nozzle diameter20%...

A Versatile Anet ET4 Wyze Cam V2 Arm Holder for the Right Side Is Now Available. Utilize an M5 x 8mm Head Cap Screw and a Matching M5 T-Nut to Secure It. ...This Attachment Can Be Easily Mounted on Either the X Bar (Front/Movable) or the Y Bar...

This was made to elevate my Wyze Cam v2 up to a level from which it could monitor my Anet a8. It was partially taken from <a href="/fallguy2006/about">Fallguy2006's</a> <a href="https://www.thingiverse.com/thing:3315051">design</a>. So far it...

This was made to elevate my Wyze Cam v2 up to a level from which it could monitor my Anet a8. It was partially taken from Fallguy2006's design. So far it elevates it perfectly. Happy printing! ... If you would like to see my other designs, go here.