wyze cam v2 target 3d models

... a playful touch to your camera, turning it into a charming creature. It easily attach's to the camera, making surveillance fun while keeping it fully functional. Give your Wyze Cam Pan V3 a unique and delightful look with these adorable additions.

Remixed from: https://www.thingiverse.com/thing:5414836 Originally designed for the Wyze Cam V3. I made the hole in the back larger, so it could fit the Wyze Cam V3 Pro. ...No supports needed, print on the back, and used PLA filament.

grab easy knobs position the WYZE pan cam for ideal tilt viewing angle with ease printed with PLA+, choose from selection on Amazon by clicking here: Click Here suggest printing threaded knobs separately for optimal thread integrity Get the "WYZE...

I have uploaded 3 files for it: 1) Combined cam mount and base (supports a bit tougher to remove) 2) Bassinet clip only (minimal support needed) 3) Wyze Camera Mount (minimal support needed) If you opt for the pieces to be printed separately, you...

... it's due since I utilized similar brackets and the same screw spacing. In the past, I had simply relied on his shelf for my basic wyze cam setup, but this time around, I wanted to avoid drilling new screw holes when installing the wyze cam pan.

I then used a M3 x 6mm LG screw with flat washer to attach the Wyze CAM (should work for v2 and v3) to the tapped hole in the adapter plate. Third, using two M3 x 8mm LG screws and flat washers I attached the adapter plate using the two clearance...

Remixed this to work with the Wyze Cam V3. ... The other remix for the V3 was a little higher than I like, so this should sit lower for the camera to be more level with the bed.

Enclosure mount for wyze cam v3 and creality enclosure. Made to slip on the post of the enclosure when assembled with tight enough tolerances to hold in place without spacers. ...Will work with 16.5mm posts.

I needed something to tilt my Wyze Cam Pan down a little bit so I designed this inclined holder. It comes with two version, with or without the shoehorn holder. ...Enjoy!

Needed a stable mount for my Wyze cam for my Kobra 2 neo, so I designed this. enjoy. ...I'm pretty sure it works with the Kobra 2 as well.

Wyze Cam Pan mount that uses the plug itself as a mounting point, so no drilling required! ...The camera itself is lightweight enough so the plug itself should support the entire setup just fine.

Simple remix of quincyicq's Wyze Cam mount for the Ender 3: https://www.thingiverse.com/thing:4518643 This should work with any 3D printer that has v-slot rails on the side.

Remix of Foden7's Wyze Cam v3 siding mount (https://www.thingiverse.com/thing:4838459) because I needed the camera to be angled ~30 degrees to the right so it was better aimed at my front door.

This mount This Wyze Cam mount was based on the mount made by cool3dp but doesnt need any extra screws, it attaches to the two bolts on the front left. ... Already tested and ready to go.

Unnecessarily complicated mounting system for a Wyze Cam V2. There are better designs on Thingiverse, DON'T PRINT THIS ONE :P New to 3D printing and just wanted to come up with my own solution in Shapr3D and test out printing threads on my new Ender...

... my 3D printer. Please see the original designer's design for the additional parts which is needed to attach this Wyze Cam mount to. ... I listed the Printer Model as CR-10 since the CR6-SE was not listed as the "printer used" in Thingiverse menu.

... to poke holes in my firewall for remote viewing or use my VPN. Adam Argo details the process of turning the WyzeCam into an OctoPrint Timelapse camera here https://medium.com/@adamargo/using-a-wyze-cam-with-octoprint-on-a-raspberry-pi-7a1c886b9afe

Case for Wyze Sensor v2. ...Provides more area for double side tape adhesion

This is my custom design for attaching a Wyze cam v2 securely to the Ender 3's bed. It's recommended that you print this part flat with supports in place. I've successfully printed it vertically without any supports, but the horizontal orientation...

After I printed and installed the awesome Prusa Mini Base by David Warboss I was unable to use the Wyze cam mount for Prusa Mini - Bottom Cut Flat by With_Maltodextrin so, I set out to find a way I could make it work.This is my current solution,...

This is a 3D printed cover designed to shield the Wyze Cam V.2 from the elements. It's not explicitly stated whether this protective casing would also be suitable for the Wyze Pan model. The two available designs feature either a flat or pointed...

This file includes only the Wyze Cam adapter component.\r\n\r\nTo bring this adapter to life, you'll need to print parts from the design linked here:\r\nArticulating Mount.\r\nhttps://www.thingiverse.com/thing:2448971\r\n\r\nPrint as many arms and...

I was wanting my white Wyze Cam V3 to be a little less noticeable and to be able to blend in more with where I was mounting it. I printed this cover in black and coupled it with a black mount, and now it is much less noticeable and "fits in" more...

The Wyze cams came with plates and magnets to mount them securely, but the pan had no mounting hardware whatsoever. I decided to create a custom mount to hang the camera from a small shelf on the wall. I drilled four holes in the back for attaching...

... when my cases were running out. ...So Figure since a wyze cam is small I would make a small bracket to hold a cam so I could monitor my case level on my tablet or phone. ...I have made 3 different versions of this mount I am currently using V3.

This mount is built to fit a WYZE Cam V3, and mounts it to a Ender 3 Pro along the rail on the lower left side. It was designed to work without any bolts or screws. It clips in and hangs on. No supports needed and to add strength print with 20+...

Mounting a Wyze Cam to the front of your Ender 3 Pro is a straightforward process, requiring you to clip it onto the front roller bracket. ...The assembly consists of three distinct components held together by two M4 screws and matching nuts.

This mount allows to mount the Wyze cam on a tripod. ...The 1/4" UNC threaded insert slot is 12.5 mm long with 7.8 mm diameter.<br/> Link to the design: <a href="https://a360.co/2A7upIY">https://a360.co/2A7upIY</a></p>

Human created a Wyze Cam base using the Modular Mounting System. This project was remixed from two other things, and you will need the mounting kit from https://www.thingiverse.com/thing:2194278. A base was created using this design:...

I remixed this right side bracket with another bracket that works for with the Wyze Cam v3 so i could use my v3 on my CR10. ... This is the other bracket i used, for some reason Thingiverse wont let me add it to the remix list...