wyze cam target 3d models

Wyze Cam Pan mount that uses the plug itself as a mounting point, so no drilling required! ...The camera itself is lightweight enough so the plug itself should support the entire setup just fine.

Remixed this to work with the Wyze Cam V3. ... The other remix for the V3 was a little higher than I like, so this should sit lower for the camera to be more level with the bed.

This mount This Wyze Cam mount was based on the mount made by cool3dp but doesnt need any extra screws, it attaches to the two bolts on the front left. ... Already tested and ready to go.

This is a Wyze cam mount to clip onto the side of the CR-10 v2. Probably works for the other CR10 variants also. ... Edit: Added a version that's a little lower to be near the bed level.

I took the Wyze cam offset mount front bar by Cerabus but needed if for the front 202 extrusion of my CR-10 v2. ...I modified the length so it would clear the bed when its fully forward.

Remix of Foden7's Wyze Cam v3 siding mount (https://www.thingiverse.com/thing:4838459) because I needed the camera to be angled ~30 degrees to the right so it was better aimed at my front door.

This also allows you to tweak the angle of the camera to your liking on the mount since the Wyze Cam can move on its base.The Wyze mount point is not the full size of the Wyze Cam V2 base, and does not need to be (it is snug!) - this allows you to...

This isn't so much a remix per se, but I adapted Zachary's Wyze Cam V2 Mount from https://www.thingiverse.com/thing:5643563 to create a V2 mount that would snap fit onto one of the support poles (approximate diameter of 15.95 mm) of my Creality...

... my 3D printer. Please see the original designer's design for the additional parts which is needed to attach this Wyze Cam mount to. ... I listed the Printer Model as CR-10 since the CR6-SE was not listed as the "printer used" in Thingiverse menu.

... to poke holes in my firewall for remote viewing or use my VPN. Adam Argo details the process of turning the WyzeCam into an OctoPrint Timelapse camera here https://medium.com/@adamargo/using-a-wyze-cam-with-octoprint-on-a-raspberry-pi-7a1c886b9afe

After I printed and installed the awesome Prusa Mini Base by David Warboss I was unable to use the Wyze cam mount for Prusa Mini - Bottom Cut Flat by With_Maltodextrin so, I set out to find a way I could make it work.This is my current solution,...

This is a 3D printed cover designed to shield the Wyze Cam V.2 from the elements. It's not explicitly stated whether this protective casing would also be suitable for the Wyze Pan model. The two available designs feature either a flat or pointed...

Ideal for those who have an older Wyze Cam V2 or V3 already mounted to the celling exactly where they want it, and wish to use the micro-USB cable already there (however you may want to swap the older USB power brick to the Pan Cam v3's power...

This file includes only the Wyze Cam adapter component.\r\n\r\nTo bring this adapter to life, you'll need to print parts from the design linked here:\r\nArticulating Mount.\r\nhttps://www.thingiverse.com/thing:2448971\r\n\r\nPrint as many arms and...

This Wyze Ender 5 Modular Mount is a combination of HeyVye's Modular Mounting System and 2 parts I designed myself to mount the Wyze Cam V2 on the Ender 5. The clip was from a GoPro mount I redesigned(the original didn't work at all so I rebuit it...

This Wyze Ender 5 Modular Mount is a combination of HeyVye's Modular Mounting System and 2 parts I designed myself to mount the Wyze Cam V2 on the Ender 5. The clip was from a GoPro mount I redesigned(the original didn't work at all so I rebuit it...

... very snug in a standard single gang outlet box. I have mine installed with no other hardware (screws), just pressure fit. If you are looking for the version of this thing that works with the Wyze Cam v2: https://www.thingiverse.com/thing:4139309

The Wyze cams came with plates and magnets to mount them securely, but the pan had no mounting hardware whatsoever. I decided to create a custom mount to hang the camera from a small shelf on the wall. I drilled four holes in the back for attaching...

I was wanting my white Wyze Cam V3 to be a little less noticeable and to be able to blend in more with where I was mounting it. I printed this cover in black and coupled it with a black mount, and now it is much less noticeable and "fits in" more...

... filament if it doesn't fit. 2. The wyze webcam monitor stand. I did not need supports for this print. Instructions to turn your Wyze Cam into a webcam: https://wyzelabs.zendesk.com/hc/en-us/articles/360041605111-Webcam-Firmware-Instructions

I used these guides for setting up my wyze cam and this cable to connect to my raspberry pi running octoprint: https://community.octoprint.org/t/new-firmware-for-wyze-convert-to-webcam/17761/3...

... when my cases were running out. ...So Figure since a wyze cam is small I would make a small bracket to hold a cam so I could monitor my case level on my tablet or phone. ...I have made 3 different versions of this mount I am currently using V3.

This mount provides a solid foundation for the Wyze Pan Cam, securely holding its weight while accommodating potential future upgrades to other cameras. The STL file's specified orientation facilitates effortless support removal, with only minor...

A low-profile shelf securely fastens the Wyze cam to the left of the print bed using the existing bolts attached directly to the main board. ...Rotate the shelf so its largest side, featuring prominent bolt holes, faces the print bed for a seamless fit...

Beautiful design by acorderob, expertly modified for my Wyze cam. I only wish I had printed it in ABS initially, as the PLA softened slightly after a lengthy heated bed print, causing it to become somewhat wobbly. ...To rectify this, I will reprint it...

Human created a Wyze Cam base using the Modular Mounting System. This project was remixed from two other things, and you will need the mounting kit from https://www.thingiverse.com/thing:2194278. A base was created using this design:...

This is a Wyze cam mount to clip onto the side of the CR-10 v2. Probably works for the other CR10 variants also. Edit: Added a version that's a little lower to be near the bed level. ...Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No...

I required clips to keep my Wyze Cam tidy on my Monoprice Mini 3D Printer. It easily secures in place with the printer's existing screws, ensuring a clean and organized workspace. ...This simple solution keeps the cord neatly tucked away, making it easy...

After printing in white, simply enlarge the small screw hole to be slightly smaller than the screw attaching the Wyze Cam v3 to the floodlight body. now slip the printed part into its place and screw in. ... you can simply set 2 cameras on the mount or...

... kit by ML_404 as they have a great fit. ...Decided to remix to add a wyze cam v3 mount to monitor my new resin printer. This part may be difficult to print on an FDM printer unless supports are used. ...If printed in resin no supports are necessary.