wyze cam holder 3d models

This is an extended arm for a wyze cam V3. Allows more range of motion. I chopped the original arm to remove the metal pin that goes in the the base. Used a small piece of painters tape to get a tight fit. There is a remix that addresses this...

Created a tripod plate mount for the Wyze Cam 2 to use with the [camera liftpod](https://www.thingiverse.com/thing:4614448) to monitor my prints. It's it a really tight fit so it won't move around printed without supports with at least 10%...

Wyze Cam Outdoor Mount. Works with multiple types of siding. Just slide it in and away you go. I used PLA but obviously a more robust filament would be better. ... Note: This is a non-commercial license and you do not have permission or rights...

Simple mount designed to attach the WYZE Cam Pan V3 to a camper slide out or any surface that is 1/2 inch thick. Suggest you use ABS or PETG for outdoor applications. 6-7mm self tapping screws are suggested. ...I added a rubberized pad inside to avoid...

Fits WYZE Cam V2 snugly, there are two retaining tabs that keep the camera from falling out of housing. Tuck the power cable into grove on bottom of housing. In the back are two keyhole brackets to mount to any vertical surface. ... The keyhole...

Remix for the Wyze Cam v3 - Indoor & Outdoor camera. Siding mount to slip between your siding panels for a non-destructive mounting option. ... I really like this mount as it is easy to move around and does absolutely zero damage to anything.

This is a spacer to mount your Wyze Cam Pan v3 a little higher up to make room for non-standard micro-usb cables on the included wall mount. You will no longer be able to use the included camera screw, so you will need a longer roughly 25mm to be...

Remix for the Wyze Cam v3 - Indoor & Outdoor camera. Siding mount to slip between your siding panels for a non-destructive mounting option. I really like this mount as it is easy to move around and does absolutely zero damage to anything. ...

Remade skooter2k5's Ikea Lack Wyze Cam Mount: https://www.thingiverse.com/thing:4638416 Removed the top lip. Enlarged the screw holes and created cavity in the corner to provide space for hot glue. Did not want to drill more holes in the Ikea Lack...

I aimed to daisy chain two Wyze cams using the Wyze camera wall mount bracket from Amazon, but when I tried to close the mount with the two USB cables attached, there wasn't enough room for them to fit inside. To resolve this issue, I resorted to...

This is a window mount for the original Wyze cam. Wyze now makes a mount for for the V2 and V3 cameras but nothing for the V1. I originally had a mount with suction cups and found that did not work very well. With this design, it mounts to a...

Well why not slap a security camera to your enclosure to make sure nothing fishy happens the moment you step away?The Wyze Cam V3 Lack mount allows you to mount a V3 Cam at a 45 degree angle, giving you a leveled view of your print.The mount features...

I created this mount so I could attach a wyze cam to a vertical 2x4 in the back of my garage. Print the mount with the open back up so as to minimize overhang. There's a smidge of overhang at the backplate slot, but the chamfer on it seems to...

The Wyze Cam boasts an integrated time-lapse feature, allowing for high-quality time-lapse video capture of your prints. This feature is particularly useful for documenting printing progress and optimizing print settings. This camera mount attaches...

I created this mount so I could attach a wyze cam to a vertical 2x4 in the back of my garage. Print the mount with the open back up so as to minimize overhang. There's a smidge of overhang at the backplate slot, but the chamfer on it seems to...

... place into the same slot the camera slides into and keeps it from sliding out at fast print speeds. I've also included cable clips that work with the Wyze Cam USB cable and can be hot glued to the curved side of the case. ...(Armor mod plate only)

A functional way of mounting the Wyze cam to the leg of a Lack table without taking the camera apart. Mount can be inverted and camera can be mounted either way up. Combined https://www.thingiverse.com/thing:4387373 and...

I designed this simple stand for my Wyze Cam Pan to elevate and stabilize it for use monitoring my 3D printer.I printed using a 0.28mm layer height at 50mm/s with 10% infill and 2 perimeters on my Ender 3 v2. No special settings are required. I used...

This is a V1.0 of a window mount for the new Wyze Cam OG. The slots for tape are for 3M automotive thin tape commonly used for car badges. There are slots for tape inside the print but unless the camera isn't mounted at 90 deg. i do not...

Position Wyze cam facing forward, but it should be possible to insert it into the mount from any angle you prefer. ... When printing, I reinforced the area around mounting screw holes with 100% infill for added strength, though this may not have been...

I needed a way to mount my Wyze cam V3s in corners of the house, since that gives a better view than most walls. I used 20mmX50mm command Velcro frame strips. I hot glue the one side attached to the print, because the strips don't adhere to the...

... mount to mount the cam to the ceiling. ...ONLY works with WYZE CAM V3, NOT the V2 Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Resolution: 0.1 Infill: 25% Filament: Hatchbox PLA White Category: Electronics

Attach a wyze v2 camera to your anycubic kobra!

This post has any possible articulation you can think of for the Wyze Cam Pan. Link 2 of these together to create a custom bracket for your camera. The center hole is designed specifically for the standard Wyze bolt (1/4-20). The smaller holes are...

Rather than drill holes in my new shed, I created a mount for my Wyze Battery Cam Pro.This piece was designed around CyberCyclist's Simple C Clamp found here: https://www.thingiverse.com/thing:5829593The mount has a slot for the clamp to slide into...

I wanted a slide in alternative to the screw holes on the new Wyze Outdoor cam so that I can move it around and mount it easier than using the holes on the base. See license: Attribution — You must give appropriate credit, provide a link to the...

Angled wedge mounts for the Wyze Doorbell Cam to correct the camera angle. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: 0.20 Infill: 30 Filament: Generic PLA Category: Replacement Parts

So I came up with a solution to mount a Wyze Cam V3.Print, Install camera & battery, Open your door - slide it down over the hinge side of the door, close door - you're done, no fasteners, no tape, no glue, no modifications to the building.My door...

... the use this design. Use at your own risk. Credits: Thanks to munchbard for making the Wyze Cam model available. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Yes Supports: No Resolution: 0.2 Infill: 40% Category: Household

... away from the crib and discontinue use once your baby is able to reach it. 4. I am not responsible for any harm caused by using this design, so please use it at your own risk. I'd like to thank munchbard for making their Wyze Cam model available.