wu tang clan logo 3d models

This is an easy-to-print Synthesizer Stand for LYRA-8 Organismic SynthesizerWill support the LYRA-8 Organismic Synthesizer or Synthesizers around 266.7MM X 266.7MM or 10.5 inches x 10.5 inchesPlaces the Synth on a comfortable 5 degree slopeNo support...

(Support Enforcers Only)Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Mods do not lift off (long build). Other parts to use with the Space Port Center Bridge Module:The original Space Port -...

----------------------------------------------------------------------------------------------------------------------- OTHER REMARKS: I designed the layout myslef: - The logo is based on figures on some other RFID products but unique. - The QR...

Now you can print them out and use them for your nefarious purposes as you travel the far and vast star systems.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

Instead of painting the Dyna-Soar shield logo I now plan to print it out on high gloss photo paper, seal it, and then glue it over the raised shield. I think that will look much better. Hope to get some more done soon and update the post! ...

Citizens will sleep safely knowing the power generated will light up the dark passageways used by heavily armed patrols, keeping the alien mutant scum from crawling into your hab, slitting your throat, and taking what's yours!Shelter...

 - BNO08x: This means the part is meant for BNO08x or MPU 9250/6500 chips- 503759: This means the part is meant for batteries that are 5x37x59mm (based on that batteries sizing).- SS22F32: This indicates the part was designed for the switches...

I also upload the firmware binary file (firmware.hex - ITALIAN LANGUAGE!) as well as the _Bootscreen.h file in which, to make the difference with the original firmware more visible, I made the same initial logo but in negative. CONFIGURATION...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod Starship Transfer Tug -...

Instead of painting the Dyna-Soar shield logo I now plan to print it out on high gloss photo paper, seal it, and then glue it over the raised shield. I think that will look much better.</p> <p>Hope to get some more done soon and update the post!</p>...

When engaged in a full frontal attack, they are quite literally, unstoppable.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

Place your ducts with 2x M3 bolts.You can adjust the height of the ducts later.Then place 2 x 5015 cooling fans with M3 nuts and bolts as shown above.Fix 40mm fan and Cover-With-Logo with 4x M3 bolt to the main body.-Place snap on Duct-Left and...

I use it on a plywood deck where my synthesizers are crowding along with my science fiction models. A support enforcer is neededNo gluingEasy to printDesigned on...

Get you Platform Walkways today and sleep safely knowing that heavily armed patrols will keep the alien mutant scum from crawling into your hab, slitting your throat, and taking what's yours!Shelter yourself! Deliver your cargo!Stay in the...

(Support Enforcers Only)Super glue works best.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules do not lift off (long build). Other parts to use with the Space Port Power Station:The original...

correct measurements, centred with hot-end *ABL sensor mount also centred, ie Y offset = 0 *Minor improvements to Mount body Update 2 *Optimised wings to not need as many supports (needs new body) *Created new body with better mounting to x-carriage...

It connects to the wire rack shelves I use to set my amps on (shelving from Home Depot).A support enforcer is needed.No gluingEasy to printDesigned on...

My filament guide does not have tubes in as I drilled out the holes a little but this is up to you. Included with the filament guide and Hot End camp STL parts you can use the optional dual colour logo's or use the NO_LOGO versions. I am using the...

Violence is never more than a heartbeat away.Use those guns! Deliver your cargo!Stay in the fight!Small painted-on supports are required for Gun overhang (Support Enforcers Only.)Can be printed without support (I did it as a test.)Resize for smaller...

- *Slime*: This part has the SlimeVR logo on it, mostly for the lid. - *Blank*: This part has no print or logo on it, mostly for the lid. ### So which parts do i need? Of course this is totally dependent on the battery and switch you chose,...

(After repairs of course)Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

remixed from theses 2 on printables https://www.printables.com/model/174959-makerdeck-logos-coins-coaster-spinners https://www.printables.com/model/292793-k2-filament-clip I like things that spin so I created this for fun but it also has a few...

This only matters if you care if the Lego logo is oriented a certain way.Tip: If your screw options are limited and they're a little too long, you can add some washers under the mounting studs. This will add a small gap between the studs and the...

That makes it possible to add a logo to the text.OpenSCAD can read a ttf font file with the “use” command. It is possible to download a font and put it in the same folder as the OpenSCAD script and use it, without having to install the font in the...

The Python code will let you move the robot, autonomously, following pre-set movement patterns with precision. Convert it into a remotely operated webcam: Control it using a Xbox/ PS4 controller: The control APP has been created with Python Take a...

The modules work with selectors to specify the primitives you want to work with, much like css or jquery: //OpenSCAD logo: differed("hole") ball(50) orient([x,y,z]) rod(d=25, h=50, $class="hole"); For more information, check out the wiki! Updates...

Details are on but will need supports and will likely be very fragile.Print separately:borealis_keelborealis_iceterrainPost-PrintingIce TerrainPrinting out the terrain with white filament works well enough, but I've attempted an interesting technique...

(Technically, the University of Kentucky logo embossed in the bottom side has tiny spans in it, but that shouldn't really count.) The central hinge uses 45-degree angles to avoid spans and the spring, which deforms harmlessly into free space (rather...

Raspberry Pi Zero and Pi Zero 2 Case Compatible with old &amp; newerPi Zero,Pi Zero 2 &amp;Pi Zero W (includes a camera ribbon slot) Snap fit design -no screws required. Heat sink hole for the 2W variation. "Coin slot" provided to prise lid open....

the small part of the Handy logo was going to be used as a wedge part for the now classic version of the Handy Holder that is belt/strap/vesa mountable. 8. Handy Grease applicators - fit in the slot of the Handy, just squeeze your grease tube into...