ws 1401 3d models

Here's some guidance to help you optimize the audio quality on your WSTER Bluetooth Speaker. To get started, ensure that the speaker is properly connected to your device via Bluetooth. Next, check the volume settings on both your device and the...

<p>I had extra samples of igus 10-40 rail on hand and I figured I'd make a small parts tray. &nbsp;My original intent was for holding heatset inserts, but this will work with screws, nuts, anything small enough to fit. &nbsp;The sample boxes come...

GPS holder

I thought the sending device could tilt a little too much back and forth, so I made sure it didn't shake off by adding the hanger. The weather sensors will be installed 25 meters up on a sloping roof where they're not easily accessible in case of...

98% precise, enough for most of the use-cases.

IGUS guide rail

Support GPS WM181 pour Bras de Quad FPVRemplissage TPU à 80%

Knobs designed specifically for screws that require a wrench size between 10 and 14mm fit perfectly snugly. To prevent the bolt from loosening, a depot is built in to be filled with resin or JBweld. The depot features a molded ring that enhances the...

back plate with connector XT60Category: Electronics

Gundam Weapons Set - 002 EF-24R Flight Rotor Shrike Includes construction manual This set was designed to be fully compatible with the following kits: 1/144 HG M1 Astray Follow the latest updates at: https://noedgesite.wordpress.com If you enjoy...

back plate with connector XT60

Radiation shield and mounts for Weatherstation

Semester project on the topic "Utopia"

Got my wife a weather station, I already had a wooden pole in the yard. so I made a flat top mount. Used a 8 inch lag screw and a 1 inch fender washer. ... mount to the flat top of your pole or 4x4 post and then secure per the instructions but try not...

Corner Mounting for Yamaha Speaker

Christmas garland made from LED strips printed on a 3D printer. The diffusers are pre-soldered WS2812B LEDs available at https://ru.aliexpress.com/item/50x-Pre-soldered-WS2812B-LED-Heatsink-5V-5050-RGB-WS2811-IC-Built-in-12cm-Wire/1941066393.html.

This adapter fits snugly onto a 1.5" PVC pipe and clamps securely to a weather station base. It also accommodates a standard 1/2" flagpole tube made from PVC, which I utilized for this project. The flagpole mount cleverly holds the tube at a precise...

Gundam Weapons Set - 004 350mm "Bulg" Rail Bazooka Designed Specifically for 3D Printing on Gundam Model Kits (Gunpla) Includes Detailed Construction Manual This set is optimized to work seamlessly with the following kits: 1/144 HG Duel Gundam...

A waveshare 1.69 inches LCD, with its rounded corners.It offers a 240x280 resolution and is driven by a ST7789 chip.Dimensionally accurate, but the backside components and 8-pins connectors aren't represented, so beware.

Thingiverse wont let me load the pics but i mounted a 1s WalkSnail Avatar VTX in my Switchback. Use the regular small gummies t mount your ESC/ FC and then push the mounts down onto the top. use your Dremel to grind down the stack screws, or use...

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

DAS Equipment

If you want / need use CM4 with PCIe TO M.2 Adapter Pi Compute Module 4 (WaveShare WS-19091) in WaveShare WS-19195 box - you will find that you cannot close original box.&nbsp;This was reason that I created new higher upper part replacement for that...

The straightforward design is swift to produce and highly efficient. This attachment enhances your printer's performance, improving print accuracy slightly. ...Additionally, it directs the filament neatly onto the rods and into the extruder,...

The initial 3D model was crafted using Sketchup 8 software, subsequently converted to various other 3D formats. The native file format is .skp. For rendering, a 3ds Max 2016 version was used along with Vray 3.00. ...This setup supports power supplies of...

Needed a canopy that 1) Can fit the Walksnail 1S lite camera (and protect the lens) 2) Fit the Meteor75pro frame 3) Uses the outer holes of the frame (I don't like when the canopy mounts to the little 25.5x25.5 standoffs that always break 4) Is...

Here is the thing! A customized version of a certain website: http://www.thingiverse.com/thing:381187. Created with the Customizer, also from Thingiverse! You can access it at http://www.thingiverse.com/apps/customizer/run?thing_id=381187.

Stable roll holder created for frame thickness of 6 millimeters. ... Print Settings: Printer: g3orgs Rafts: Not Required Supports: Not Needed Resolution: 0.25 millimeters Notes: Easy to print with PLA material.

The initial 3D model was designed using Sketchup 8 software, later converted into various 3D formats. ...The native file format is .skp, and it has been rendered with Vray 3.00 in a 3ds Max 2016 scene utilizing a Port Catalyst 3560G 24 processor.

This three-dimensional model was originally designed using Sketchup 8 before being translated into every other 3D format possible. The original native format is .skp, while the 3dsmax scene runs on a high version of 3ds Max 2016, all seamlessly...