wrx phone mount 3d models
429884 3d models found related to wrx phone mount.thingiverse
Phone holder designed specifically for 2015+ Subaru WRX models. It perfectly fits into the console bin located under the radio, elevating your phone to a comfortable viewing position in front of the shifter. ...The phone tray was meticulously crafted to...
prusaprinters
For my son's Subaru WRX 2006, he wanted to mount a new badge on the car front grill. So, a clamp that fits into the front grill mesh was needed. The mesh is coated steel. Here is my 3D printed solution. To keep the screw mount short, I cut a 8g x...
thingiverse
To keep the screw mount compact, I shortened an 8g x 12mm self-tapping screw by cutting off a length to make the threaded area 7mm long. There are two 3D printed parts: a top section and a bottom section. The bottom section is bonded to the back of...
thingiverse
If you're having trouble sliding the original mount into the 3D printed mount, use a lighter to slightly heat the slot, then slide the original mount in. Slide the bolt through the hole, put the nut on, and screw the bolt into the stub. A small bit...
thingiverse
Remixed from a similar design, i opened up the phone area as i have a large note in a heavy case, also added something to fill in the empty space is originally had. Print with PETG or ABS as PLA will melt inside of a car. ...Print with supports...
thingiverse
Gauge mount for 02 - 07 WRX just gotta drill out holes for the screws to slide in
thingiverse
This is a 2015+ WRX defroster vent mount for a Cobb Accessport remixed from dasfruit. I added vent fins, enclosed the portion of the mount around the cable holder, and added a clip to keep the cable from coming out of the mount. I also added tabs...
thingiverse
This design replaces the stock mount that wiggled and failed to hold the AP well, providing a snug fit and keeping everything tight. To assemble the parts, test-fit the clamp on the dash, then attach the angle with the AP3 holder mounted to it. Mark...
thingiverse
I also boomed it out and up a little higher, as I don't utilize the cubby for anything other than my phone charger and just wanted the phone a little higher than others. Customized version of https://www.thingiverse.com/thing:3125740 Created...
thingiverse
Multiple phone types are accommodated here, including the iPhone 5s and LG G3 models. Upgrades Added: •STI Version •XV Version **Installation Instructions** These instructions were printed on a Makerbot 5th Generation device. Printed settings...
thingiverse
... to provide better structural integrity at a measurement of 10. Adding personal flair to each individual piece by changing the default message to Wrx. ... Setting the ideal height of each wooden rod using stick thicknesses in the order of 4.
thingiverse
I'm installing a Subaru WRX side defroster vent mount on my Cobb Accessport, and I've found that it fits perfectly without needing any additional hardware. The vent holds the accessport securely in place. I've tested this setup on my 2018 WRX model.
thingiverse
Designed this front camera mount for 2015-2021 WRX/STi models Pretty straight forward installation, just a bit intimidating pulling off the front bumper having never done this before. Routed the wiring over the driver side wheel well, through one...
thingiverse
This is a custom center vent mount designed specifically for a 52mm boost gauge to perfectly fit inside the interior of an 08-13 WRX or STI. To achieve seamless fitment, you need to remove two essential components: the horizontal and vertical vent...
thingiverse
This is a personalized adaptation of the Thing found at http://www.thingiverse.com/thing:58001. ...It was made using the Customizer tool available at http://www.thingiverse.com/apps/customizer/run?thing_id=58001, which allows for customization of...
thingiverse
Specifically designed to sit perfectly centered in the dash grill, this mount sinks in just enough to allow for seamless installation of OEM cover panels. The screws drop into place with ease, producing a clean and smooth finish that enables you to...
thingiverse
The mount features a fully functional tunnel, louvers, cable clip, and of course the actual mount itself. It has been thoroughly tested and trialed. You should print this in ABS/PETG or it will melt under direct sunlight. The picture shown is...
thingiverse
This unit holds a 10mm thick tablet snugly within the upper din of the 2002 WRX's radio mount securely.
thingiverse
Remixed this off Jasonjones's design, thanks Jason. Added some curves to prevent it digging into the dash and added screw holes to add some adjustability. recommend using some pads on the inside of the grip to help it grip. Use PETG or ABS to...
thingiverse
Customized version of https://www.thingiverse.com/thing:3125740 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3125740
cults3d
... controller. ... Easy to remove and reuse the factory hardware to mount this new part in place. Fits: 05 -07 Wrx/Sti but might fit some other years and Foresters as well but check photos to make sure you have the same shifter trim/center console
thingiverse
Here is a recessed mounting bracket designed specifically for Alpine SPS-610C super-tweeters, perfect for replacing stock speakers in a 2016 Subaru WRX dashboard. Since both sides of this design are mirror images, you'll only need to create one and...
cults3d
... This vent mount perfectly matches the fit and finish of the OEM vent and makes installing your Accessport super simple. This mod is perfectly reversible and will not harm the original parts. The factory defrost function works perfectly still.
cults3d
Replace the factory dash defrost vent in your 2007 - 2014 Subaru Impreza WRX/ STI and mount your Cobb Accessport. Check photos to make sure this is the correct part for your car. Includes the LH and RH versions with .stl and .step files No...
thingiverse
This is a tweeter bracket for the WRX tweeters in a 2015+ model vehicle. It should fit most 1.5-inch tweeters with a 42mm mounting hole. The print settings include using the Robo 3D printer, specifically the R1 ABS + PLA Model. The raft and support...
thingiverse
This was a phone mount I created and it fits about any phone on the market and can even probably fit your phone case too! ...Fits a good selection of screws that could drill into a 2 by 4.
thingiverse
Charging Station Companion: A Hands-Free Phone Mount Designed to Keep Your Device Safe and Secure When Plugged In