wrench holders and organizers 3d models

* holders for 1/4" and 3/8" sockets. * 4" rail fits ~8 1/4" holders or ~5 3/8" holders depend on socket width. * 6" rail fits ~8 3/8" holders. printing the rails on their side will keep them smooth (seems to work better for me), printing them...

This model is designed to hold metric and standard wrench sets.

I designed these in TinkerCAD to better organize the playing table/box and to ease set-up/clean-up of the fully expanded Killer Bunnies and the Quest for the Magic Carrot.  Set-up and clean-up is now a breeze.  Also, the original Rank card...

... there but none for Kobalt. 3/8 shallow and Deep combo set - Metric You need a 300x300 build area to print these. 6/17/19 - Added US socket set, fixed an issue with the metric short socket length 6/24/19 Added Standard and Metric wrench set holders.

**Installation Instructions** The Organizer Kit Contains Four Units, Two Designed for Short Wrenches and Two Designed for Longer Wrenches. This Accommodation Covers Both Standard and Metric Wrenches Present in the Set. ... **Standard Size Options**...

I designed these in TinkerCAD to better organize the playing table/box and to ease set-up/clean-up of the fully expanded Killer Bunnies and the Quest for the Magic Carrot. Set-up and clean-up is now a breeze. Also, the original Rank card stands...

Magnets used are 12 x 3 mm and attached using superglue (I highly recommend BSI InstaCure with accelerant). ...The only 2 holders in the picture not 3D printed are from Ernst (and are bigger than my print bed).

... ... * Optional holes on bottom for 10x3mm magnets. * Magnets not necessary to function properly ** v2 update ** * Better dovetail and magnet fitment * changed units from inch to mm * added second set of files for holding slightly wider wrenches

Made on tinkercad. ...metric and fractional wrench holder for peg board

3 to 18 wrenchs at a time organizers 30 Different organizers!

... I included a .step if you want to change the size. With magnets that strong, I noticed that I only needed them on the ends and they hold to the bottom of my tool drawer just fine. Yes, I'm missing wrenches from this set, hence my need to organize!

My Simple and Easy to Print Take on a Wall mounted socket And wrench holdersprints with minimal supports (print laying on pack with support under socket pegs)mounts to wall with standard drywall or deck screws 3 drive sizes (1/4", 3/8", and 1/2")...

Here are three different options for Gridfinity wrench drawers I built. They fit a drawer that will fit a 15x15 Gridfinity grid. My drawer is in a Vidmar cabinet, but it should fit most industrial storage cabinets. ... Now with step files so you can...

Here is the 2nd part of organizing an old tap and die set I got from my grandfather. Each holder contains common sizes up to 1/2" / M12, with up to four taps of each size that can be stored. If you have a drawer full of loose taps, these would...

Anyway some 3/8 and 1/2 socket holders as I had to organize my toolbox. 1/4 is not finalizer yet. See Pics for socket sizes. Had to split these into a 3 piece set to fit on the build plate of my ender 3v2. Magnet pocket to hold together if needed...

Flexible wrench holder One is for .25 inch wrenches to .625 inch wrenches One is for .625 inch wrenches to 1.5 inch wrenches

... with each posting). Most of these wrenches are older Craftsman models, and the larger Metric set is a mix of both thinner older Kobalt branded wrenches and newer 2018 Kobalt wrenches. ... I have also added Harbor Freight specific wrench holders.

Made these clamps for holding my new 10 pcs metric wrench set. tip: Determine the correct mounting position with wrenches clamped in them! note: for 3 clamps (8/9 10/11 and 12/13) you need smaller screws to mount them Category: Tool Holders & Boxes

... wrenches. ... tip: To ensure optimal performance, it's crucial to determine the correct mounting position with wrenches securely clamped in place! ... note: For three clamps (8/9, 10/11, and 12/13), you'll need smaller screws to secure them properly.

A Handy Holder Keeps 7 Mini Wrenches Organized A handy holder is used to store and display seven compact mini wrenches. ... These small wrenches were purchased from an online marketplace called eBay at the following link:...

These are card holders/organizers that I designed to hold the cards for Star Wars Imperial Assault because it has a lot of these cards but they will also work for other cards that are roughly 40mm X 63mm. ... In the future I intend to add some...

This compact wrench holder is designed to accommodate up to 10 pieces of both SAE and metric wrenches, making it a versatile and space-saving solution for your tool storage needs.

The 19 pc holder measures 283 mm in length and 235 mm in width, requiring careful attention during printing on a CR-10 printer due to its snug fit, which necessitated precise placement of bed clips and skirt dimensions. ... Other wrench holders are...

There is a single and double of the full size and I added a double in a smaller size for more compact storage of smaller wrenches. Probably would work for screwdrivers etc too, I haven't got there yet. ...I'm using these for wrenches up to 1-½" or so...

The correct holder exists for everything from tiny full polish 6mm to massive 80s craftsman chunky 1-inch box wrenches and every size in between. Most modular wrench holders I've encountered are either one-size-fits-all or limited to a fixed wrench...

Functional tap wrench holders for use into pegboards. The download includes three diferent sizes. ... #0 - Hole 5mm (M3, M4, M5) #1 - Hole 7mm (M6, M7) #2 - Hole 8mm (M8)

Belt clip holster for both metric and standard Allen wrench sets, designed to hold your tools securely in place. The holes for the wrenches are a bit snug at first, but with use, they'll loosen up nicely. On the back, you'll find a spot where a piece...

Primarily recommended for use as an organizer, though can also be used as a planter for plants which tolerate the enclosed space well (small top surface area of soil for diffusion, please do not overwater your plant-friends.) No one can resist that...

To hold 3/8 drive sockets and wrenches below it.