wrapping paper holder and cutter 3d models

There are not one but two size options available - a 51mm diameter and a 60mm diameter, making it easy to wrap larger rolls of wrapping paper with precision and ease.

A wrapping paper cutter using single edge blades. Original was printed with 4 perimeters, but it can be printed with 30-50% infill. Support is required on the body for the overhang on the upper lid guide. User assumes responsibility for the safe...

Then grab the blade again with the pliers, grip tightly, and push all the way in until the tip of the blade sits inside the slot in the plastic wall. This redesign is specifically designed to hold easily found surgical blades, such as code 10A,...

... For this specific design, holder thickness is 2.2mm, holder height is 10mm, roll diameter is 4.7cm, and there's only one holder. The cut angle for the holder is 69 degrees. ... Remember to keep it within 60 words as instructed.

... designed using the Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=261712) with specific settings: holder height of 10mm, roll diameter of 4.7cm, a cut angle of 50 degrees, one count and a thickness of 2.2mm for the holder.

... All can be printed without any supports. I have seen any comments / post regarding that similar wrapping paper cutters do not work or break. I myself googled 'Little ELF' and watch the instructional video on how to use a similar product. ...

Created this wrapping paper cutter for larger sized wrapping paper rolls (70mm) but can also work on smaller sized rolls. This uses X-Acto #11 blades. There are several options for logos for the outside: NoLogo, SnowFlake, Snowman, ChristmasTree,...

Features: Rounded edges are designed to prevent snags A tapered exit after the cutter is included to prevent snags, a problem that was encountered during original testing The diameter is suitable for most rolls Height has been optimized to reduce...

This is a handheld version of my other design for the wrapping paper slicer with a utility blade. This does not require and hardware and allows the blade to be replaced. ...Insert a pencil on the release button to allow the parts to slide apart.

This should fit all wrapping paper sizes and will save on print time! EDIT 2: Check out: https://www.thingiverse.com/thing:5161220 for a smaller version yet. This is a new design based on the first. I did some playing with the shaping of the...

Modeled by HerzogsHandicraft Printed and works as expected, the blade is pretty tight in slot Features: - Insert X-Acto #11 blade from the bottom, and then insert a toothpick into the hole and break off, glue if needed - Tapered after it passes blade...

I was inspired by the original design for the cylindrical wrapping paper cutting tool and designed this from scratch with a slot for an X-ACTO #11 blade plus a handle to help hold the tool and a hinged door for a Scotch pop-up tape insert. These...

I downsized the original design because it was too bulky for my taste. I created a slimmer, more compact version that can still accommodate ten A-blades. ...When it comes to printing, there's not much to say - it's just a straightforward circular shape.

Another remix for a minimalist version. Still uses an X-ACTO #11 blade. ...Print Settings Rafts: Doesn't Matter Supports: No Category: Hand Tools

I've updated the design to ensure compatibility with the 10 Blade. A test print is included, so you can verify the blade fits before investing four hours in a print. ...To see it in action, check out this quick video: https://youtu.be/kcgcOXJhJ5o

Here's the updated manual for using two X-Acto blades to minimize damage.

A fresh take on minimalism is unfolding, built around a precision-cutting tool - the trusty X-ACTO #11 blade.

added snowflake patterns

Remade from the ground up for a regular, precision-crafted X-ACTO #11 blade. Check out this streamlined version... ... https://www.thingiverse.com/thing:3281921

Wrapping paper cutter with an ordinary Snap-Off Utility Knife (9 mm) Bring the paper cutter flush with the roll, gently press together so that the blade goes through the paper and simply pull (push) along the roll. The blade is easy to change...

Wrapping paper cutter with an ordinary Snap-Off Utility Knife (9 mm) Bring the paper cutter flush with the roll, gently press together so that the blade goes through the paper and simply pull (push) along the roll. The blade is easy to change...

This is a remix to fit a utility blade in the “Wrapping paper cutter” by Over_I have tested Husky blades, and Milwaukee iron-carbide edge blades. The husky ones drop straight in, and the Milwaukee ones are a hair tight, but do fit. ...The Milwaukee ones...

This is a remix to fit a utility blade in the “Wrapping paper cutter” by Over_I have tested Husky blades, and Milwaukee iron-carbide edge blades. The husky ones drop straight in, and the Milwaukee ones are a hair tight, but do fit. ...The Milwaukee ones...

Wrapping paper cutter with an ordinary Snap-Off Utility Knife (9 mm) Bring the paper cutter flush with the roll, gently press together so that the blade goes through the paper and simply pull (push) along the roll. The blade is easy to change because...

The revamped design boasts an expanded inner diameter of 70 mm to accommodate larger rolls of wrapping paper, specifically tailored to fit those from BJ's. However, I'm uncertain if this would also work with the large rolls sold at Costco. The blade...

Remix of Aero3D's Christmas Gift Wrap Cutting Machine for massive rolls from Costco. ...Inner circumference measures an impressive 85 millimeters.

Hallo ich habe hier mir einen einfache Halterung erstellt zur Lagerung von Geschenkpapier.

# Instructions Printed on an MK3S+ using Prusament PETG

Baking paper, foil, stretch, wrapping and sizing machine.barbaroskarakoc@gmail.com